07
06
AIR SUPPLY AND CONNECTIONS
The connector on the tool must not hold
pressure when air supply is disconnected.
Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.
Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool.
If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line
is disconnected, possibly causing injury.
Use
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal injury.
The regulated pressure must not
exceed 100psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
Always disconnect air resource:
◆
Before unloading or making adjustments.
◆
When maintaining the tool.
◆
When clearing a jam.
◆
When touching the safety yoke.
◆
When tool is not in use.
◆
When moving to a different work area.
Such precautionary measures reduce the risk
of injury to persons.
Over pressurizing the tool is able to result in
bursting, abnormal operation, breakage of the
tool or serious injury to persons. Use only clean,
dry, regulated compressed air at the rated
pressure or within the rated pressure range as
marked on the tool. Always verify prior to using
the tool that the air source has been adjusted to
the rated air pressure or within the rated air-
pressure range.
●
●
●
LOADING TOOL
Do not load the tool with fasteners when any
one of the operating controls is activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
●
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
WARNING:
!
UNPACKING
This tool has been shipped completely
assembled.
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call
.
1-866-676-8468
●
●
●
●
●
●
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse
and could result in hazardous condition
leading to possible serious personal
injury.
WARNING:
!
OPERATION
●
FEATURES
360 ADJUSTABLE EXHAUST
OIL-FREE DESIGN
COMFORT-GRIP HANDLE
ERGONOMICALLY ENGINEERED BODY
°
Allows user to direct air away from debris.
For less maintenance.
For long lasting durability.
For increased comfort and control.
ANODIZED ALUMINUM CYLINDER AND
MAGAZINE
AIR FILTER
ADJUSTABLE DEPTH
QUICK-JAM RELEASE
NON-MARRING SAFETY CONTACT
Rugged and Comfortable resulting in a light-
weight tool great for extended use.
Keeps interior components debris free, extending
tool life.
Depth is easily adjustable for various
applications.
Allows for easy access clearing in the event of a
jam.
Eliminates damage to working surface.
●
●
●
●
●
●
●
●
FEATURES
SPECIFICATIONS
REQUIRES:
AIR INLET:
MAGAZINE CAPACITY:
WEIGHT:
MAXIMUM PRESSURE:
PRESSURE RANGE:
5.87 SCFM with 100
fasteners per minute @ 90psi
1/4 inch NPT
100 fasteners, 18 gauge
2.58 lbs
100psi
60psi 100psi
–
PIN SIZE RANGE:
1/2 inch to 1-1/4 inch
Compatible With All Generic 18 Gauge 1/4"
Crown Staples From 1/2" To 1-1/4".
●
●
●
●
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
Connect the tool to the air resource.
Push down on the latch button(B). Pull back on
the magazine cover(C).
Push the magazine cover(C) forward until latch
button pops up.
Load a clip of fasteners with the crowns
straddling the magazine rail(D).
⒈
⒉
⒊
⒋
LOADING FASTENERS
Latch button(B)
Magazine rail(D)
Magazine cover(C)
