Husqvarna 10530SBEB Owner'S Manual Download | Manualshive

Page: 29 / 32

background image

29

KEY PART
NO. NO.

DESCRIPTION

   1   532 18 10-44   Spring, Traction Idler
   2   532 18 05-22   Pulley, Idler (2-1/4)
   3     - - -      Engine, Briggs & Stratton,

Model Number 20E114
(For engine service and
replacement parts,
call Briggs & Stratton
at 1-800-233-3723)

   4   874 78 05-20   Screw, Hex Head 5/16-18 x 1-1/4
   5   532 15 00-78   Screw, Hex Head 5/16-18 x 3/4
   6   532 05 92-89   Washer, Flat
   7   873 93 05-00   Nut, Jam, Lock 5/16-18
   8   532 17 53-30   Pin, Idler Pivot
   9   532 17 90-92   V-Belt, Traction Drive

10 810 04 05-00 Washer, Lock 5/16

11 817 49 05-08 Screw, Hex Head 5/16-18 x 1/2

12   532 17 92-59   Impeller Arm / Pad Assembly
13   532 08 51-79   Retainer, Hairpin
14   532 17 88-28   Spring, Brake
15   532 18 35-33   V-Belt, Impeller Drive
16   532 19 23-06   Screw, Hex Head 3/8-16 x 1-1/4
17   532 18 48-04   Arm, Idler
18   874 78 05-24   Screw, Hex Head 5/16-18 x 1-1/2
19   532 17 53-31   Bushing, Idler Pivot
20   532 18 05-23   Pulley, Idler (2-3/4)
21   874 61 05-16   Screw, Hex Head 5/16-18 x 1
22   532 17 93-71   Spacer, Engine Pulley
23   532 18 04-78   Pulley, Engine, Traction Drive
24   532 17 91-57   Pulley, Engine, Impeller Drive
25   532 06 27-35   Washer, Flat 3/8
26   532 85 02-63   Washer, Lock, Helical 3/8
27   532 85 10-84   Screw, Hex Head 3/8-24 x 1-3/8
28   532 15 54-52   Guide, Belt

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO.

10530SBEB

(96193001300), PRODUCT NO. 961 93 00-13

KEY PART
NO. NO.

DESCRIPTION

29 532 19 22-13 Belt Cover Assembly

(Includes Toolbox Cover)

30   532 17 88-30   Cover, Toolbox
31   817 49 04-08   Screw, Hex Head 1/4-20 x 1/2
32   532 17 92-56   Bolt, Shoulder 5/16-18
33   532 18 78-53   Bellcrank Shifter
34   532 18 04-01   Screw, Hex Head 1/4-28 x 3/4
35   532 19 57-67   Arm, Auger Control
36   873 80 05-00   Nut, Lock 5/16-18
37   532 18 40-86   Bellcrank
38   532 18 71-01   Link, Speed Control
39   532 19 21-10   Trunnion, Pivot Bracket
40   532 17 88-20   Nut, Cage 3/8-16
41   532 70 02-79   Hairpin, Cotter 3/32 x 1/2
42   532 17 90-65   Pin, Pivot Bracket
43   532 18 40-85   Bracket, Bellcrank
44   871 21 06-16   Screw, Hex Head
45   532 18 40-74   Pivot Bracket, Impeller Idler Arm
46   532 18 40-84   Pan, Frame Bottom
47   871 02 05-12   Screw, Hex Head 5/16-18 x 3/4
48   532 18 11-56 Nut, Speed 5/16-18
49   532 40 39-09   Frame Assembly
50   532 18 80-02   Plate, Frame End
51   532 19 95-14   Shaft, Auger Control
52   532 05 70-79   Washer, Hardened
53   532 19 22-75   Roller
54   532 19 21-47   Ring, Crescent
55   812 00 00-02   E-Ring
56   532 40 39-08   Plate, Enging Mounting
57   811 05 05-00 Washer, Lock, External Tooth 5/16
58   532 19 30-70   Power Cord
59   532 19 97-25   Deﬂ ector, Mufﬂ er
60   532 19 97-26   Screw

NOTE:

All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT:

Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your lawn mower and void your warranty.

«
...
27
28
29
30
31
...
»

Summary of Contents for 10530SBEB

































Reviews:

No comments

Related manuals for 10530SBEB

Brand: Yardworks Pages: 18

Brand: Yard-Man Pages: 16

Straw Blower 1800

Brand: Harper Pages: 42

Sweepmaster P900 R

Brand: HAKO Pages: 64

Brand: ICP Pages: 12

Brand: SNOWJOE Pages: 20

Pro Landscaping DCM587

Brand: DeWalt Pages: 136

Brand: Cub Cadet Pages: 16

Brand: KENT Pages: 52

Brand: Dustcontrol Pages: 82

Brand: Poulan Pro Pages: 41

Brand: Scarab Pages: 36

Brand: Tennant Pages: 66

PRO RDP-SEBV20 SOLO

Brand: Raider Pages: 56

Brand: JDW Pages: 13

Brand: Garland Pages: 112

Brand: SaMASZ Pages: 28

Brand: ebm-papst Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands