background image

English – 

23

FEDERAL AND CALIFORNIA EMISSION CONTROL

WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (The US Environmental Protection Agency), CARB
(California Air Resources Board) and Husqvarna Forest &
Garden are pleased to explain the emissions control system
warranty on your 1999 and later small off-road/nonroad
engine. In U.S., new small off-road/nonroad engines must be
designed, built and equipped to meet the federal and
California stringent anti-smog standards. Husqvarna Forest &
Garden must warrant the emission control system on your
small off-road/nonroad engine for the periods of time listed
below provided there has been no abuse, neglect or
improper maintenance of your unit. Your emission control
system includes Parts such as the carburetor and the ignition
system.
Where a warrantable condition exists, Husqvarna Forest &
Garden will repair your small off-road/nonroad engine at no
cost to you. Expenses covered under warranty include
diagnosis, parts and labor.

MANUFACTURER’S WARRANTY
COVERAGE

The 1999 and later small off-road/nonroad engines are
warranted for two years. If any emission related part on your
engine (as listed above) is defective, the part will be repaired
or replaced by Husqvarna Forest & Garden.

OWNER’S WARRANTY
RESPONSIBILITIES

As the small off-road/nonroad engine owner, you are
responsible for the performance of the required maintenance
listed in your Operator’s Manual. Husqvarna Forest &
Garden recommends that you retain all receipts covering
maintenance on your small off-road/nonroad engine, but
Husqvarna Forest & Garden cannot deny warranty solely for
the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road/nonroad engine owner, you should,
however, be aware that Husqvarna Forest & Garden may
deny you warranty coverage if your small off-road/nonroad
engine or a part of it has failed due to abuse, neglect,
improper maintenance, unapproved modifications or the use
of parts not made or approved by the original equipment
manufacturer.
You are responsible for presenting your small off-road/
nonroad engine to a Husqvarna Forest & Garden authorized
servicing dealer as soon as a problem exists. The warranty
repairs should be completed in a reasonable amount of time,
not to exceed 30 days.
If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at
1-800-487-5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small off-road/
nonroad engine is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner and
each subsequent purchaser that the engine is free from
defects in materials and workmanship which cause the
failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS
Repair or replacement of any warranted part will be performed
at no charge to the owner at an approved Husqvarna Forest &
Garden servicing dealer. If you have any questions regarding
your warranty rights and responsibilities, you should contact
your nearest authorized servicing dealer or call Husqvarna
Forest & Garden at 1-800-487-5963.
WARRANTY PERIOD
Any warranted part which is not scheduled for replacement as
required maintenance, or which is scheduled only for regular
inspection to the effect of ”repair or replace as necessary”
shall be warranted for 2 years. Any warranted part which is
scheduled for replacement as required maintenance shall be
warranted for the period of time up to the first scheduled
replacement point for that part.
DIAGNOSIS
The owner shall not be charged for diagnostic labor which
leads to the determination that a warranted part is defective, 
if the diagnostic work is performed at an approved Husqvarna
Forest & Garden servicing dealer.
CONSEQUENTIAL DAMAGES
Husqvarna Forest & Garden may be liable for damages to
other engine components caused by the failure of a warranted
part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance
are not covered.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest & Garden is
not liable to cover failures of warranted parts caused by the
use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at
1-800-487-5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part
used in the performance of any warranty maintenance or
repairs on emission-related parts, will be provided without
charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1. Carburetor and internal parts
2. Intake pipe, airfilter holder and carburetor bolts.
3. Airfilter and fuelfilter covered up to maintainance schedule.
4. Ignition System

a) Spark Plug, covered up to maintenance schedule
b) Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual.

Summary of Contents for 3120K

























Reviews: