Husqvarna 927SBEXP Owner'S Manual Download | Manualshive

Page: 19 / 32

background image

19

Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.

  equipped) in OFF position.
  2.    Safety ignition key      2.    Insert safety ignition key.
  is not inserted.
  3.    Out of fuel.      3.    Refi ll fuel tank with fresh, clean gasoline.
  4.    Throttle in STOP position.   4.    Move throttle to FAST position.
  5.    Choke in OFF position.       5.    Move to FULL position.
  6.    Primer not depressed.      6.    Prime as instructed in the Operation section of this manual.
  7.    Engine is fl ooded.     7.    Wait a few minutes before restarting, DO NOT prime.
  8.    Spark plug wire is       8.    Connect wire to spark plug.
  disconnected.
  9.    Bad spark plug.   9.    Replace spark plug.
  10. Stale fuel.    10. Empty fuel tank & carburetor, refi ll with fresh, clean gasoline.
  11. Water in fuel.    11. Empty fuel tank & carburetor, refi ll with fresh, clean gasoline.

Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.

  2.    Throwing too much snow.   2.    Reduce speed and width of swath.
  3.    Fuel tank cap is covered   3.    Remove ice and snow on and around fuel tank cap.
  with ice or snow.
  4.    Dirty or clogged muffl er.    4.    Clean or replace muffl er.

Engine idles or 1. Choke is in FULL position. 1. Move choke to OFF position.
runs roughly 2. Blockage in fuel line. 2. Clean fuel line.

  3.    Stale fuel.    3.    Empty fuel tank & carburetor, refi ll with fresh, clean gasoline.
  4.    Water in fuel.    4.    Empty fuel tank & carburetor, refi ll with fresh, clean gasoline.
  5.    Carburetor is in need of      5.    Contact a qualifi ed service centre.
  adjustment or overhaul.

Excessive 1. Loose parts or damaged 1. Tighten all fasteners. Replace damaged parts.
vibration augers or impeller. If vibration remains, contact a qualifi ed service centre.

Recoil starter 1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”
is hard to pull in the Operation section of this manual.

Loss of traction    1.    Drive belt is worn.     1.    Check / replace drive belt.
drive / slowing    2.    Drive belt is off of pulley.   2.    Check / reinstall drive belt.
of drive speed      3.    Friction drive wheel is worn.     3.    Contact a qualifi ed service centre.

Loss of snow    1.    Auger belt is off of pulley.     1.    Check / reinstall auger belt.
discharge or     2.    Auger belt is worn.      2.    Check / replace auger belt.
slowing of     3.    Clogged discharge chute.     3.    Clean snow chute.
snow discharge    4.    Augers / impeller jammed.      4.    Remove debris or foreign object from augers / impeller.

TROUBLESHOOTING

PROBLEM CAUSE CORRECTION

See appropriate section in manual unless directed to a qualifi ed service centre.

«
...
17
18
19
20
21
...
»

Summary of Contents for 927SBEXP

































Reviews:

No comments

Related manuals for 927SBEXP

Brand: Topfloor Pages: 24

Brand: Wel-Bilt Pages: 7

Brand: Simplicity Pages: 28

Pro Force 44553

Brand: Toro Pages: 44

Brand: Garland Pages: 40

Brand: Minuteman Pages: 18

Snow Line 620E III

Brand: AL-KO Pages: 84

Brand: Kobalt Pages: 24

Brand: Tuthill Pages: 34

Brand: Snapper Pages: 4

Brand: Snapper Pages: 8

Brand: Snapper Pages: 8

Brand: Snapper Pages: 24

Brand: Snapper Pages: 24

Brand: Snapper Pages: 20

Brand: Homestead Pages: 15

Brand: Gude Pages: 120

Brand: Farm King Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands