manualshive.com logo in svg

Husqvarna CS 2156, Operator'S Manual

The Husqvarna CS 2156 Chainsaw is a powerful and reliable tool designed for professionals and enthusiasts alike. Ensure safe and efficient operation with the Operator's Manual. Download it for free from 88.208.23.73:8080 to access comprehensive instructions, troubleshooting tips, and maintenance guidelines for maximizing the performance and longevity of your equipment.

Share
Download
background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

6

 

 – 

 

English

 

Bef

 

ore using a new chain saw

 

•

 

Please read this manual carefully.

•

Check that the cutting equipment is correctly fitted 
and adjusted. See instructions under the heading 
Assembly.

•

Refuel and start the chain saw. See the instructions 
under the headings Fuel Handling and Starting and 
Stopping.

•

Do not use the chain saw until sufficient chain oil has 
reached the chain. See instructions under the 
heading Lubricating cutting equipment.

•

Long-term exposure to noise can result in permanent 
hearing impairment. So always use approved hearing 
protection.

 

Impor

 

tant

Always use common sense

 

It is not possib

 

le to cover every conceivable situation you 

can face when using a chain saw. Always exercise care 
and use your common sense. Avoid all situations which 
you consider to be beyond your capability.  If you still feel 
uncertain about operating procedures after reading these 
instructions, you should consult an expert before 
continuing. Do not hesitate to contact your dealer or us if 
you have any questions about the use of the chain saw. 
We will willingly be of service and provide you with advice 
as well as help you to use your chain saw both efficiently 
and safely. Attend a training course in chain saw usage if 
possible. Your dealer, forestry school or your library can 

!

 

W

 

ARNING! Under no circumstances may 

the design of the machine be modified 
without the permission of the 
manufacturer. Always use genuine 
accessories. Non-authorized 
modifications and/or accessories can 
result in serious personal injury or the 
death of the operator or others.

!

 

W

 

ARNING! A chain saw is a dangerous 

tool if used carelessly or incorrectly and 
can cause serious, even fatal injuries. It 
is very important that you read and 
understand the contents of this 
operator’s manual.

!

 

W

 

ARNING! The inside of the muffler 

contain chemicals that may be 
carcinogenic. Avoid contact with these 
elements in the event of a damaged 
muffler.

!

 

W

 

ARNING! Long term inhalation of the 

engine’s exhaust fumes, chain oil mist 
and dust from sawdust can represent a 
health risk.

!

 

W

 

ARNING! This machine produces an 

electromagnetic field during operation. 
This field may under some 
circumstances interfere with active or 
passive medical implants. To reduce the 
risk of serious or fatal injury, we 
recommend persons with medical 
implants to consult their physician and 
the medical implant manufacturer before 
operating this machine.

 

IMPOR

 

TANT!

This chain saw for forest service is designed for forest 
work such as felling, delimbing and cutting.
You should only use the saw with the bar and chain 
combinations we recommend in the chapter Technical 
data.
Never use the machine if you are fatigued, while under 
the influence of alcohol or drugs, medication or anything 
that could affect your vision, alertness, coordination or 
judgement.
Wear personal protective equipment. See instructions 
under the heading ”Personal protective equipment”.
Do not modify this product or use it if it appears to have 
been modified by others.
Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures 
must be carried out by trained and qualified specialists. 
See instructions under the heading Maintenance.
Never use any accessories other than those 
recommended in this manual. See instructions under 
the headings Cutting equipment and Technical data.
CAUTION! Always wear protective glasses or a face 
visor to reduce the risk of injury from thrown objects. A 
chain saw is capable of throwing objects, such as wood 
chips, small pieces of wood, etc, at great force. This can 
result in serious injury, especially to the eyes.

!

 

W

 

ARNING! Running an engine in a 

confined or badly ventilated area can 
result in death due to asphyxiation or 
carbon monoxide poisoning.

!

 

W

 

ARNING! Faulty cutting equipment or 

the wrong combination of bar and saw 
chain increases the risk of kickback! 
Only use the bar/saw chain combinations 
we recommend, and follow the filing 
instructions. See instructions under the 
heading Technical  data.

Summary of Contents for CS 2156













































Reviews:

No comments

Related manuals for CS 2156

Zenoah G2200T Owner'S Manual preview
G2200T
Brand: Zenoah Pages: 20
Ribimex 515246 User And Maintenance Manual preview
515246
Brand: Ribimex Pages: 59
pellenc Selion C21 HD Operating Instructions Manual preview
Selion C21 HD
Brand: pellenc Pages: 44
Worx WG368E Original Instructions Manual preview
WG368E
Brand: Worx Pages: 204
HENX A40LJ14B01 Operator'S Manual preview
A40LJ14B01
Brand: HENX Pages: 77
STERWINS 3276007088533 Assemby - Use - Maintenance Manual preview
3276007088533
Brand: STERWINS Pages: 43
Cub Cadet LH5 C60 Original Operating Instructions preview
LH5 C60
Brand: Cub Cadet Pages: 278
SHARKS SH 4500 Instruction For Operation And Maintenance preview
SH 4500
Brand: SHARKS Pages: 54
Valex 1491964 Instruction Manual And Safety Instructions preview
1491964
Brand: Valex Pages: 20
Mac allister MCSW40-2 Original Instructions Manual preview
MCSW40-2
Brand: Mac allister Pages: 63
Mac allister 5059340255873 Original Instructions Manual preview
5059340255873
Brand: Mac allister Pages: 63
Raider Power Tools RD-GCS15 User Manual preview
Power Tools RD-GCS15
Brand: Raider Pages: 72
Zenoah G415AVS Operator'S Manual preview
G415AVS
Brand: Zenoah Pages: 24
Parker PCS-2600 Owner'S Manual preview
PCS-2600
Brand: Parker Pages: 29
Feider Machines FTRTPRO40 Instruction Manual preview
FTRTPRO40
Brand: Feider Machines Pages: 20
Echo CS-2511TES Service Manual preview
CS-2511TES
Brand: Echo Pages: 88
Tanaka ECS-3300 Owner'S Manual preview
ECS-3300
Brand: Tanaka Pages: 35
SGS 58CC Owner'S Manual preview
58CC
Brand: SGS Pages: 46

Brands by name

Popular brands

Load more brands