background image

Lifting point on the safety frame.

Do not attach the lifting equipment at this

point. (L)

Noise emission to the environment as

referred to in the EC directive. The emission

of the product is specified in 

Noise and

vibration declaration statement on page 17

and on the label.

This product is in compliance with applicable

EC directives.

Note: Other symbols/decals on the product refer to

special certification requirements for some markets.

Type plate

4

6

7

5

3

1

2

1. Product type
2. Product number
3. Product weight
4. Serial number
5. Manufacturer
6. Rated power
7. Production year

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage

to the product, other materials or the

adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

General safety instructions

WARNING: Read the warning instructions

that follow before you use the product.

• This product is a dangerous tool if you are not

careful or if you use the product incorrectly. This

product can cause serious injury or death to the

operator or others. Before you use the product, you

must read and understand the contents of this

operator’s manual.

• Save all warnings and instructions.
• Comply with all applicable laws and regulations.
• The operator and the employer of the operator must

know and prevent the risks during operation of the

product.

4

1388 - 001 - 

Summary of Contents for LFV 100





















Reviews:

Related manuals for LFV 100