background image

3

REGISTER THE PRODUCT

Please register your new Power Pack with Husqvarna Construction Products by mailing  

in the registration card that came with the machine or you can register on the internet site 

www.husqvarnawarranty.com

Registration will allow us to contact in case of any critical updates or recalls on this machine.  
Warranty registration has also been found to be helpful in tracing stolen equipment.

Record the following information for your records:

PURCHASE DATE: ________________

MODEL No: ________________ 

 

SERIAL No: __________________

ENGINE MODEL: _____________   ENGINE TYPE: ______________  ENGINE CODE: ________________

The power pack model and serial number as well as the engine model number, engine type and code are critical 
in order to obtain the correct service parts.  Husqvarna Construction Products does not supply any engine service 
parts.  Engine parts are distributed through the engine manufacturer’s dealer network.  
Please refer to the BRIGGS & STRATTON Operator’s Manual that was included with the machine.

SAFETY HAZARDS

CAUTION

HEARING HAZARD

During the normal use of this 
machine, operator may be 
exposed to a noise level equal 
to or higher than 85 dB(A).  Use 
hearing protection. 

WARNING

ASPHYXIATION HAZARD

Running an engine in a con-
fi ned or badly ventilated area 
can result in injury or death due 
to asphyxiation or carbon 
monoxide poisoning.

WARNING

CALIFORNIA PROP 65

Use of this product can expose 
you to materials known to the 
State of California to cause 
cancer and/or birth defects or 
other reproductive harm.

WARNING

DO NOT MODIFY THE PRODUCT

Under no circumstances may the design of the machine be modifi ed without the permission of the manu-
facturer. Always use genuine accessories.  Unauthorized modifi cations and/or accessories can result in 
serious personal injury or the death of the operator or others.  Your warranty may not cover damage or 
liability caused by the use of unauthorized accessories or replacement parts.

SAFETY DEFINITIONS

In this manual a Safety Alert Symbol         followed by the signal words WARNING and CAUTION are used to 
identify safety information about hazards which can result in death, serious injury and/or property damage.

These signal words mean:

  
        WARNING 

indicates a hazard which, if not avoided, 

could result in death or serious injury.

        CAUTION 

indicates a hazard which, if not avoided, 

might result in minor or moderate injury.

        NOTICE 

indicates a message not related to personal injury.

 

Summary of Contents for PP 418





















Reviews: