background image

12

Immediately prepare your tiller for storage at the end of 
the season or if the unit will not be used for 30 days or 
more.

CAUTION:  Never store the tiller with 
gasoline in the tank inside a build ing 
where fumes may reach an open fl ame 
or spark.  Allow the engine to cool 
before storing in any en clo sure.

TILLER

•      Clean entire tiller (See “CLEANING” in the Customer 

Responsibilities section of this manual).

•      Inspect and replace belts, if necessary (See belt re-

 place ment instructions in the Service and Ad just ments 
section of this manual).

•      Lubricate as shown in the Customer Responsibilities 

section of this manual.

•      Be sure that all nuts, bolts and screws are securely 

fastened.  Inspect moving parts for damage, break age 
and wear.  Replace if necessary.

•      Touch up all rusted or chipped paint surfaces; sand 

lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT

IT IS IMPORTANT TO PREVENT GUM 

DEPOSITS FROM FORMING IN ES SEN TIAL FUEL SYS TEM 
PARTS SUCH AS THE CAR BU RE TOR, FUEL FILTER, FUEL 
HOSE, OR TANK DURING STOR AGE. ALSO, EXPERIENCE 
INDICATES THAT AL 

CO HOL BLENDED FUELS (CALLED 

GASOHOL OR USING ETHA 

NOL OR METHA 

NOL) CAN 

ATTRACT MOIS TURE WHICH LEADS TO SEPA RA TION AND 
FORMATION OF ACIDS DUR ING STOR AGE. ACIDIC GAS 
CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE 
IN STOR AGE.

•      Drain the fuel tank.
•      Start the engine and let it run until the fuel lines and 

carburetor are empty.

•      Never use engine or carburetor cleaner products in 

the fuel tank or permanent damage may occur.

•      Use fresh fuel next season.

NOTE

:  Fuel stabilizer is an acceptable alternative in mini-

mizing the formation of fuel gum deposits during stor age.  
Add stabilizer to gasoline in fuel tank or stor age container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to 
allow the stabilizer to reach the carburetor.  Do not drain 
the gas tank and car bu re tor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil.  
(See “ENGINE” in the Customer Responsibilities section 
of this man ual).

CYLINDERS

•      Remove spark plug.
•     Pour 1 ounce (29 ml) of oil through spark plug hole 

into cylinder.

•     Pull starter handle slowly several times to distribute 

oil.

•      Replace with new spark plug.

OTHER

•      Do not store gasoline from one season to another.  
•         Replace your gasoline can if your can starts to rust.  Rust 

and/or dirt in your gasoline will cause problems.

•      If possible, store your unit indoors and cover it to give 

protection from dust and dirt.

•     Cover your unit with a suitable protective cover that 

does not retain moisture.  Do not use plastic.  Plastic 
cannot breathe which allows condensation to form 
and will cause your unit to rust.

IMPORTANT

: NEVER 

COVER 

TILLER 

WHILE 

EN 

GINE AND 

EX HAUST AREAS ARE STILL WARM. 

STORAGE

Summary of Contents for TS 20



















Reviews: