background image

This warning does not mean that Hussmann products 
will cause cancer or reproductive harm, or is in 
violation of any product-safety standards or 
requirements. As clarified by the California State 
government, Proposition 65 can be considered more of 
a ‘right to know’ law than a pure product safety law. 
When used as designed, Hussmann believes that our 
products are not harmful. We provide the Proposition 
65 warning to stay in compliance with California State 
law. It is your responsibility to provide accurate 
Proposition 65 warning labels to your customers when 
necessary. For more information on Proposition 65, 
please visit the California State government website.

August 31, 2018

 

This warning does not mean that Hussmann products 
will cause cancer or reproductive harm, or is in 
violation of any product-safety standards or 
requirements. As clarified by the California State 
government, Proposition 65 can be considered more of 
a ‘right to know’ law than a pure product safety law. 
When used as designed, Hussmann believes that our 
products are not harmful. We provide the Proposition 
65 warning to stay in compliance with California State 
law. It is your responsibility to provide accurate 
Proposition 65 warning labels to your customers when 
necessary. For more information on Proposition 65, 
please visit the California State government website.

August 31, 2018

 

BEFORE YOU BEGIN

Read these instructions completely and carefully. 

PERSONAL PROTECTION EQUIPMENT (PPE)

Personal Protection Equipment (PPE) is required whenever installing or servicing this equipment. Always wear 
safety glasses, gloves, protective boots or shoes, long pants, and a long-sleeve shirt.

IMPORTANT

KEEP IN STORE FOR FUTURE REFERENCE

Quality that sets industry standards!

12999 St. Charles Rock Road • Bridgeton, MO 63044-2483 

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900

www.hussmann.com

© 2019 Hussmann Corporation

®

®

®

®

®

P/N 3093114_A

Summary of Contents for BEXDW8G













































Reviews:

Related manuals for BEXDW8G