background image

14

Front Coils 
controlled by 
EPR Valve 
under 
Deck Pan

T-Stat & 
Ballast Are 
Labeled as 
Such

(Located in the 
same place for 
hot and cold)

Optional 

T-Stat and 

Solenoid

(Right Side)

Figure #3

Refrigeration Data

Note: This data is based on store temperature and humidity
that does not exceed 75F and 55% R.H.

Front

Top

See Spec Sheet

Note: Not recommended to control temp by regulating coil
temp allow T-STAT to cycle and control temp.

Front

Top

Btu/hr/ft*

See Spec sheets

Parallel

Conventional

*For all refrigeration equipment other than Hussmann, 
use conventional Btu values.

Defrost Data

See Spec Sheets

Frequency Hrs

OFFTIME

Temp Term °F

Failsafe Minutes

ELECTRIC or GAS Not Recommended

Refrigeration (Cont'd)

Physical Data

Merchandiser Drip Pipe (in.)

1½*

Merchandiser Glycol Pipe (in.)

7/8*

Merchandiser Liquid Line (in.)

3/8*

Merchandiser Suction Line (in.)

5/8*

Estimated Charge (lb)***

4ft

1.2

5ft

1.5

6ft

1.8

*Dependent on case length and refrigerant type.

*** This is an average for all refrigerants types. Actual 
refrigerant charge may vary by approximately half a 
pound.

GLYCOL REQUIREMENTS

GPM

PSI

NA

NA

NA

NA

NA

NA

Summary of Contents for CR3HV-ND
































Reviews: