Hussmann Excel F Installation & Operation Manual Download

Page: 6 / 68

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

P/N 0467434_P

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

P/N 0467434_N

REVISION HISTORY

REVISION L

1. FWGH and FWGEH Load Limit Profile
2. FWGH and FWGEH Bolt Location Drawings Page

1-10, 1-12

3. Added Replacing Product Side Heater
4. Flue Glass for FWGH 1-21

REVISION K

1. Updated Prep Merchandiser #2, page 1-5.
2. Added Replacing Interior Panels and Louvers, page

1-14.

3. Added coil cleaning, page 5-3.
4. Revised Step 6, page 6-8.

REVISION J

1. Removed adjustable legs, page 1-3, throughout.

REVISION I — not used

REVISION H

1. Added 3-in. space requirement from walls, page 1-3
2. Added merchandiser lineup bumper instruction to

Offsetting Bumper Section, pages 1-15 to 1-18.

3. Added Drip Piping Support 24 in. requirement from

Drain Hubs, pages 3-2 and 3-3

4. Added Rail Heater wiring harness drawings, pages

6-3 to 6-6.

REVISION G

1. Revised drip piping pitch, page 3-1.
2. Added stainless steel rail maintenance, page 5-2.

REVISION F

1.  Added Joining Merchandisers in Line
  (3 photos). page 1-6.
2.  Added Bumper Retainer Bracket drawing, page 1-7.
3.  Added Joining End Merchandiser to Wide Island (3

photos), page 1-8.

4. Added Socket Adapter Photo, page 1-10, 1-12.
5. Removed “V” from drawing FW to FWE,

page 1-12.

6.  Added Bumper Retainer photo, page 1-15.
7.  Revised instruction information, page 1-15.
8.  Added NOTES, page 1-6 to 1-9.
9.  Changed bumper tool information, page 1-14.
10. Added Replacing Hand Rail Heater, page 6-3 to

6-4.

REVISION E

1. Added ANSI definitions, page iv.
2. Added bumper removal instruction to Offsetting

Bumper, pages 1-12 — 1-14.

3. Added offsetting plastic hand rail procedure, page

1-15.

4. Added SS Top Rail Joint Trim, page 1-16.
5. Added Installing Flue Glass — FNG & FIG, page

1-17.

6.  Updated NSF Thermometer, pages 4-3 and 4-4.
7.  Added center flue removal instruction, page 5-3.
8.  Updated WARNING, CAUTION, and NOTICE

boxes throughout.

9. Added URL, contact phone numbers to bottom of

even-numbered pages.

REVISION D

1. Changed to factory installed flange nut fastener

for joining end merchandiser to wide island parent,
page 1-7.

2. Changed

key

on page 1-8; affects joining

illustrations on pages 1-8 and 1-9.

3. Changed joining order, page 1-8.
4. Changed 3 in. Hex Head screw to 3

in. Hex Head

screw, pages 1-8 and 1-10.

5. Changed

end

key

on page 1-10.

6. Added fastener location for joining FWG to

FWEG, page 1-10.

REVISION C

1. Added URL, contact phone numbers, page iii.
2. Removed alignment pin from joining sequence,

pages 1-5, 1-6, 1-8, 1-9, 1-10 and 1-13.

3. Changed

key

on page 1-8.

4. Changed

end

key

on page 1-10.

5. Changed 4 in. screw to 4

in.

TAP

bolt, page 1-10.

6.  Deleted one location from end joining, page 1-10.
7.  Added refrigeration shroud, page 2-1.
8.  Added Do not use coarse paper towels, page 5-1.

REVISION B

1.  Added joining location, pages 1-8 and 1-9.
2.  Changed fastening order for joining, page 1-10.
3.  Added Louver Retainer, page 5-2.
4.  Added Wireway Cover, page 6-4.

REVISION A

1. Added note, page 3-2.

ORIGINAL ISSUE —

September 2005