background image

For Medium Temperature Merchandisers

D5ELE/D5EE END CASES 

TO D5 PARENT CASE

JOINING INSTRUCTION  

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

®

1

B

e sure Merchandisers have

been leveled according to the
installation instructions.
Carefully unpack and inspect
the Joint Kit making sure
there is no breakage or
damage.

1

R

EMOVING

S

HIPPING

B

RACES

Remove 

Bolts, Washers

and

Nuts 

from 

Shipping Braces.

Then remove the shipping
brace 

Brackets.

See 

Figure 1

and 

Detail A.

After removing the braces
and brackets, make sure to
replace the screws that hold
the top panels in place.

July, 2000

P/N 407199

JOINT KITJOINT KIT

Fig. 1.

Removing Shipping Braces

Side View

Bracing

PARTS LIST
Item

Quantity

Description

19" Front

23" Front

1.

1

1

Gasket 

1/

2

1/

2

x 60

2.

1

1

Gasket 

1/

2

x 1

5/

8

x 120

3.

4

4

Joining Brackets

4.

12

12

Hex Washer Head SM Screw 

3/

4

10 -16

5

2

4

Cap Screw 

5/16

-18 x 4

6.

2

4

Flat Washer 

5/16

7.

8

8

Cap Screw  

1/4

- 20 x 1

8.

8

8

Flat Washer 

1/4

9.

2

2

Cap Screw 

5/16

- 18 x 2

1/

2

10.

4

4

Flat Washer 

5/16

11.

2

2

Lock Washer

5/16

12

2

2

Hex Nut 

5/16

- 18

13.

2

2

Threaded Rod 

1/2

-13 x 15

14.

4

4

Flat Washer 

1/2

15.

4

4

Hex Nut 

1/2

-13

16.

1

1

Butyl Tape

17.

2

2

Splashguard Joint Support

18.

8

8

Hex Head Sheet metal Screw  #8 x 

1/2

Note: 

Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each

merchandiser.

Detail A

Sheet Metal
Screws

Summary of Contents for IMPACT D5ELE








Reviews: