background image

2

 

P/N 3091736_C 

U.S. & Canada 1-800-922-1919 • Mexico 1 800-890-2900 • www.hussmann.com

BEFORE YOU BEGIN

Read these instructions completely and carefully. 

PERSONAL PROTECTION EQUIPMENT (PPE)

Personal Protection Equipment (PPE) is required whenever installing or servicing this  
equipment. Always wear safety glasses, gloves, protective boots or shoes, long pants, and a 
long-sleeve shirt.

1.  If  the information in these instructions are not followed exactly, a fire or explosion may result, causing property damage, personal  
  injury or death.
2.  Installation and service must be performed by a qualified installer or service agency.
3.  This unit is designed only for use with R-290 (propane) gas as the designated refrigerant. 

THE REFRIGERANT LOOP IS SEALED. ONLY A QUALIFIED TECHNICIAN SHOULD ATTEMPT TO SERVICE!

•  Propane is flammable and heavier than air.
•  It collects first in the low areas but can be circulated by the fans.
•  If  R-290 (propane) is present or even suspected, do not allow untrained personnel to attempt to find the cause.
•  The propane gas used in the unit has no odor. 
•  The lack of  smell does not indicate a lack of  escaped gas.
•  If  a leak is detected, immediately evacuate all persons from the store, and contact the local fire department to advise them that a pro  
  pane leak has occured.
•  Do not let any persons back into the store until the qualified service technician has arrived and that technician advises that it is safe to  
  return to the store.
•  A hand-held propane leak detector (“sniffer”) shall be used before any repair and/or maintenance.
•  No open flames, cigarettes or other possible sources of  ignition should be used inside the building where the units are located until 
  the qualified service technician and/or local fire department determines that all propane has been cleared from the area and from the  
  refrigeration systems.
•  Component parts are designed for propane and non-incendive and non-sparking. Component parts shall only be replaced with identical  
  repair parts.

FAILURE TO ABIDE BY THIS WARNING COULD RESULT IN AN EXPLOSION, DEATH, INJURY AND PROPERTY DAMAGE.

Summary of Contents for Q2SSNM4SPA





























Reviews: