background image

22

 

P/N 3091736_C 

U.S. & Canada 1-800-922-1919 • Mexico 1 800-890-2900 • www.hussmann.com

Do NOT Use:

• Abrasive cleansers and scouring pads, as 

these will mar the finish.

• Coarse paper towels on coated glass.

• Ammonia-based cleaners on acrylic parts.

• A hose on lighted shelves or submerge the 

shelves in water.

• Solvent, oil or acidic based cleaners on any  

interior surfaces.

• A hose on rail lights, canopy lights or any 

other electrical connection.

Do:

• First turn off refrigeration, then disconnect 

electrical power.

• Remove product and loose debris.

• Thoroughly clean all surfaces with soap 

and hot water. 

d

o

 

not

 

use

 

steAm

 

or

 

high

 

wAter

 

pressure

 

hoses

 

to

 

wAsh

 

the

 

interior

.

 t

hese

 

destroy

 

merchandiser

s

 

sealing

 

causing

 

leaks

 

and

 

poor

 

performance

.

• Take care to minimize direct contact between 

fan motors and cleaning or rinse water.

• Rinse with hot water, but do NOT flood. 

• Allow merchandiser to dry before resuming 

operation.

• Wipe down lighted shelves with a damp 

sponge or cloth so that water does not enter 
the light channel.

 d

o

 

not

 

use

 

A

 

hose

 

or

 

submerge

 

shelves

 

in

 

wAter

.

• After cleaning is completed, restore power 

and turn on the merchandiser.

Product will be degraded and may spoil if 

allowed to sit in a non-refrigerated area.

Do NOT allow cleaning agent or 

cloth to contact food product.

Summary of Contents for Q2SSNM4SPA





























Reviews: