background image

R

P/N 2402398 A

5-1

MAINTENANC

Maintenance

 

Long life and satisfactory performance
of any equipment is dependent upon the
care given to it. To insure efficient
operation, proper sanitation and
minimum maintenance, the cabinet
should be thoroughly cleaned, debris
removed and the interior cleaned
regularly. 
 

CAUTION 

TO AVOID PERSONAL INJURY OR 

DAMAGE TO ELECTRICAL 

COMPONENTS, ALWAYS 

DISCONNECT UNIT FROM MAIN 

POWER SOURCE BEFORE 

SERVICING OR CLEANING. 

 

Cabinet Surfaces (Interior and
Exterior) 

To preserve finish, the cabinet should
be cleaned with a mild solution of soap
and warm water only, using a soft cloth
or sponge. The white plastic top is
made of a tough ABS plastic. It is
strong, clean and durable. It can be
cleaned by wiping with a damp cloth
and, if necessary, a cleaner such as
Bon Ami could de used. DO NOT use
any type of caustic soap, abrasive
cleaner, or steel wool scouring pads
which can mar the cabinet finish. 
 
The inside of your Spot Merchandiser
has been coated for long life. It will give
many years of trouble free service.
Never use a sharp instrument to chip off
frost as this may damage the liner. 
 

Condenser 

The air cooled condenser should be
cleaned regularly. A dirty condenser
restricts air flow,  

causing decreased refrigeration
efficiency. (Clean every month or as
required). 
 
1) With main power supply disconnected,
remove louver grill from front of lower
cabinet. Most dirt will collect on the air
intake side of the condenser. This is
opposite the fan motor. 
 
2) Use a bristle brush to loosen the dust
and dirt and remove with a vacuum
cleaner. When cleaning condenser line
beware of fin edges as they are sharp. 
 
3) If the Spot Merchandiser is located in
an area susceptible to grease collecting
on the condenser, scrub with a solution
of warm water and detergent. Care
should be taken to keep solution away
from wiring and electrical components. 
 

Merchandiser Electrical Data 

Spot Merchandiser data sheets are
attached to the back of this manual. The
data sheets provide case electrical data,
electrical schematics, parts lists and
performance data. Refer to the Spot
Merchandiser data sheets and case
serial plate for electrical information. 

Summary of Contents for SM









Reviews: