background image

Give  original  installation  date  of  cabinet  and, if possible, forward a copy of the  original in-
voice  or  delivery  receipt.

All  shipments  of  in-warranty  replacement  parts  will  be  invoiced  from  the  factory until
such  time  as  the  defective  part  is  returned and  proven  to  be  defective  by  our  Quality Con-
trol  Department.

Contact  your  Hussmann  Distributor  for  instructions  on  returning  in-warranty  parts.

Warranty  parts  must  be  returned  to  the  factory within  30 days of date  of failure  to  assure
proper  disposition.

Lack  of  any  of  the  above  information may  result in the  shipment  of the wrong  part,  or a
delay  in  shipment.

Replacement  compressors will not be  shipped from the  Hussmann  factory.   They  may be
obtained  from  your  nearest  Copeland  Wholesaler.

Your wholesaler will replace, free of charge,  any compressor  found to  be defective within
twelve  months of installation, not to  exceed twenty months from the date of manufacture,
as  determined  by  the  compressor  serial  number  on  the  compressor  serial  plate.

For  any  defective  compressor  beyond  the  twelve  or  twenty  month  time  period,  a  salvage
value  credit will  be  given  too  partially  offset the  invoice  for  the  replacement.

To  obtain  reimbursement  forward  to:  Hussmann  Corporation
                                                                  140 East State Street
                                                                 Gloversville, NY
                                                                 12078
       the following information:

The  cabinet  model  and  serial  number

A copy of the wholesaler’s  invoice,  along with  a  copy  of the  salvage  value  credit.

       WIRING DIAGRAMS  ARE  ATTACHED  AT  THE  BACK  OF  THIS  BOOKLET

Page 13

Summary of Contents for USL-2
















Reviews: