background image

Rev. 0505

2 3

Limited Warranty

This warranty is made to the original user at the original installation site and is not transferable.
Hussmann merchandisers are warranted to be free from defect in material and workmanship under normal use

and service for a period of one (1) year from the date of original installation (not to exceed fifteen (15) months from the
date of shipment for the factor y).  Hussmann Impact Modular Coils are warranted for a total of five (5) years
based upon the above criteria.  Hussmann’s obligation under this warranty shall be limited to repairing or exchanging
any part or parts, without charge F.O.B. factory or nearest authorized parts depot within said period and which is proven
to the satisfaction of the original manufacturing plant warranty group to be thus defective.

Hussmann covers the entire case or refrigeration product and all its components (except for lamps, driers, fuses,

and other maintenance type replacement parts) for the one (1) year warranty period.

Additionally, Hussmann warrants for a total period of three (3) years all sealed, multi-glass assemblies except

those used in sliding doors on closed meat display cases.  If within three (3) years from the date of installation (not to
exceed thirty-nine (39) months from the date of shipment from factory), it shall be proven to the satisfaction of  the
originating factory warranty group that there is impaired visibility through the multi-glass assemblies thereof caused by
moisture between the glasses, the multi-glass assembly will be replaced free of charge, F.O.B. factory.  This additional
warranty excludes accident, misuse, or glass breakage.

On Hussmann manufactured self-contained display cases, Hussmann agrees to repair or exchange, at its option,

the original motor/compressor unit only with a motor/compressor of like or of similar design and capacity if it is shown to
the satisfaction of Hussmann that the motor/compressor is inoperative due to defects in factory workmanship or material
under normal use and service as outlined in Hussmann’s “Installation Instructions” which are shipped inside new Hus-
smann equipment.  Hussmann’s sole obligation under this warranty shall be limited to a period not to exceed five years
from date of factory shipment.

On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assem-

bly is available, but must be purchased prior to shipment to be in effect.  Hussmann reserves the right to inspect the job
site, installation and reason for failure.

The motor/compressor warranties listed above do not include replacement or repair of controls, relays, capaci-

tors, overload protectors, valve plates, oil pumps, gaskets or any external part on the motor/compressor replaceable in the
field, or any other part of the refrigeration system or self-contained display case.

THE WARRANTIES TO REPAIR OR REPLACE ABOVE RECITED ARE THE ONLY WARRANTIES, EXPRESS,

IMPLIED OR STATUTORY, MADE BY HUSSMANN WITH RESPECT TO THE ABOVE MENTIONED EQUIPMENT,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND HUSSMANN NEITHER AS-
SUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT, ANY OTHER OBLIGATION OR LIABILITY IN CON-
NECTION WITH THE SALE OF SAID EQUIPMENT OR ANY PART THEREOF.

THIS WARRANTY SHALL NOT APPLY TO LOSS OF FOOD OR CONTENTS OF THE EQUIPMENT
DUE TO FAILURE FOR ANY REASON.  HUSSMANN SHALL NOT BE LIABLE:

• For payment of labor for any removal or installation of warranted parts;
• For any repair or replacements made without the written consent of Hussmann, or when the equipment is installed or

operated in a manner contrary to the printed instructions covering installation and service which accompanied such
equipment;

• For any damages, delays, or losses, direct or consequential which may arise in connection with such equipment or part

thereof;

• For damages caused by fire, flood, strikes, acts of God or circumstances beyond its control;
• When the equipment is subject to negligence, abuse, misuse or when the serial number of the equipment has been

removed, defaced, or altered;

• When the equipment is operated on low or improper voltages
• When the equipment is put to a use other than normally recommended by Hussmann (i.e. deli case used for fresh

meat);

• When operation of this equipment is impaired due to improper drain installation;
• For payment of refrigerant loss for any reason;
• For costs related to shipping or handling of replacement parts.

Hussmann Corporation, Corporate Headquarters:  Bridgeton, Missouri, U.S.A. 63044

August 1, 1998

Summary of Contents for VGD

























Reviews: