background image

AR-40 Parts List

P/N

Description

Qty

5084800

Rotator Unit ...........................…………………………….............. 1

5172600

Control Unit 110 VAC ...........……………………................... 1 or

5079610

Control Unit 220 VAC ...........……………………........................ 1

5030500

Lower Mast Support ...........……………………….........................1

5042510

Accessory Kit.....................…………………………..................... 1

107632061

Screw, 6-32 x 3/8 round head slotted .…………….................... 2

110820035

Screw, 1/4"-20 x 1 1/4" hex head .......………………................ 4

5033900

Terminal Cover ............,_..............………………………...........1

5035100

Mast Clamp..........................…………………………................ 4

5035200

U-Bolt.................……………………………..........................:..4

5050200

Flat washer …………………………………………..……………4

5091400

Grommet ……………………………………..…………………..1

556960

Nut, 1/4"-20 hex ………………………………………………….8

567115

Lockwasher, 1/4" split...................……………………............ 12

Factory Service

For units that are in warranty, no charge will be

made for any repair work required. Include a copy

of your sales receipt. For out-of-warranty units,
call the Customer Service Department for prices
and shipping authorization.

Hy-gain
308 Industrial Park Road
Starkville, Mississippi 39759 USA

The price includes rebuilding the unit, replacing
all defective and/or worn parts, and return freight
charges. Hy-Gain reserves the right to change
prices at its option. when returning items for re-
pair, a check or money order for the repair
charges must be included. Be sure to include your
name, address, zip code, and telephone number.
Also, give a brief description of the problem.

Complete Service Manuals for rotator products
can also be obtained from the factory.

If service is required, the unit must be packed
securely and sent prepaid to:

Summary of Contents for AR-40







Reviews: