background image

S E C T I O N   1   G E N E R A L

D E S C R I P T I O N

General

The Hy-Gain Model DB-1015A is a three element, duo-bander that operates on 10 and
15 meters. Hy-Gain's Hy-Q traps allow multibanding. The antenna fits a 1

1/4

” – 2

1/2

O.D. mast and can be rotated with a heavy duty TV rotator.

Specifications

Electrical

Input impedance …………………………......................................................52 ohms
Gain …………………………………........................................................... 8 dB minimum
Front-to-back ratio ……………………………................................................... 20 - 25 dB
Maximum power input ……………………………………………………………….. 1 kW AM
VSWR (at resonance) ..........................…......................…………………………….. 1.2:1
Lightning protection .....................................……………………………............DC ground

Mechanical

Boomlength....………………………………………......................................................... 12'9"
Boom diameter .............……………………….…………..….............................…...........… 2”
Longest element ......……………………………........................................... 23' maximum
Maximum wind survival .........……..………………………......................................... 80 mph
Net weight……………………………................................................. 32

lbs. approximately

Accepts mast ....………………………...................................……………...............1

5/8

" O.D.

Wind surface area .....................…………………………………..............................3.8 sq. ft.
Wind load (80 mph) .........………………………………….........................................97.3 lbs.

Theory of Operation

Hy-Gain Hy-Q traps are air dielectric parallel resonant circuits which operate as
electronic switches. On 10 meters the "switch" is open so only the inner portions of the
e!ements are operative, giving a three element, 10-meter beam. On 15 meters the

switch" is closed and the entire element is operative, giving a three element, 15-meter

beam.

The exclusive beta match matches the antenna input impedance to 52-ohm coaxial
cable and puts the entire structure at DC ground for lightning protection.

S E C T I O N   1 1   AS S E M B L Y   AN D

I N S T A L L A T I O N

WARNING

Avoid any accidental contact with power lines or any overhead obstructions by
ladders or lnstallatlon equipment. Failure to exercise care could result In serious
Injury.

Summary of Contents for DB-1015A












Reviews: