2.2
2.3
BLADE STOP BUTTON
- Stops the blade. If the blade is stopped during a cycle, the cycle will
continue but will not let the head descend until the blade is started
EMERGENCY STOP
- This mushroom button stops the blade and hydraulic motors. Both vises
will hold their position but pressure will begin to fall off. Long pieces of work should always be
supported so they will not become loose over time and fall while the machine is shut down.
BOTTOM ROW
CHIP CONVEYOR
- This switch controls the optional hydraulic chip conveyor. The chips can be
emptied to the left or right of the saw.
OUTFEED VISE
- This switch has three positions, OPEN, HOLD and CLOSE. With the switch
held in the OPEN position the vise will open all the way or until the switch is released. With the
switch in the HOLD position, the vise will stay where it is and will not move freely although it will
not resist a large force indefinitely without creeping. In CLOSE, the vise will close all the way, or
until it encounters enough resistance to stop it.
GUIDE ARM
- This switch controls the position of the distance between the guide arms by mov-
ing the upper guide arm.
WORK LAMP
- This option switch has two positions, OFF and ON.
HEAD RETRACT LIMIT OVERRIDE
- This button overrides the head retract limit switch to
allow the head to retract further in order to allow easier blade removal. Depressing this button
and either one of the head swing buttons simultaneously will also allow the head to swing at
any point along the travel of the head.
Note: These instructions are specific to the V-18APC bandsaw with serial numbers beginning
with: Serial # K0797074
Summary of Contents for V-18 APC
