2.6
2.7
F2
•
F3
•
F4
•
MANUAL MODE
After entering an angle value, pressing F2 will cause the screen to read “TO INTIATE MOVE-
MENT TO XX.X DEGREES PRESS CYCLE START”. Upon pressing “CYCLE START” the
head will swing to the programmed angle.
AUTO MODE
Used to scroll up through job information.
MANUAL MODE
Used for accessing the KERF screen. The KERF screen cannot be accessed while in MET-
RIC mode and any change made to the KERF value will not be accepted by the controller
until it has been shut down and restarted.
AUTO MODE
Used to scroll down through job information
MANUAL MODE
Used to clear the length display (shuttle vise position) value.
Used to exit “MOVEMENT TO ANGLE” screen.
AUTO MODE
Used to CLEAR job or QUEUE values at the cursor position.
CURSOR KEY PAD
- The cursor keys are used to navigate the cursor box on the
screen. If the display has columns, only the UP and DOWN keys are activated. If the
display has both rows and columns, then all four cursor keys are activated. The dou-
ble vertical cursor keys are used to PAGE UP and DOWN. Depressing the PAGE
DOWN cursor key will cause the cursor to go to the bottom of the column it is in.
SINGLE PART CYCLE OPERATION
In MAN mode, the PLC allows the operator to initiate a “Single Part Cycle “ to cut one piece at a desired
length. To accomplish this, follow this procedure.
1. Position the head for the required angle by using the 45L or 45R function keys. You can also accom-
plish this by moving the cursor to the “Angle Go” feature, input desired angle, press ENTER. To change
the L or R angle, press ENTER and the L or R will switch to the other. Then press F2. The screen will
display “TO INITIATE ANGLE MOVEMENT PRESS CYCLE START”. Press CYCLE START and the
head will travel to the displayed angle. Change the SAW VISE switch to “HOLD” to exit back to the
manual screen.
2. A trim cut should be made before initiating the “Single Part Cycle “ operation.
3. To enable the “SINGLE PART CYCLE”, the infeed vise must be in the CLOSED position.
4. Make sure the head is set so that the blade is behind and the guide arm is above the material and the
head selector switch is in the HOLD position.
5. To the left of the F1 button, the display will be flashing. Cursor the rectangular box to this section and
key in the desired length using the numeric key pad and press enter.
6. If the blade is not running, you will be prompted by the word “BLADE” flashing on the display window.
Start the blade and adjust the blade speed as required.
7. You will then be prompted by the word “START” flashing on the display window to begin the cut. Press
CYCLE START button and the cycle will begin. When the CYCLE START button is pressed, (if the
shuttle is not in HOME) the shuttle vise will move to the forward home position before executing the
Summary of Contents for V-18 APC
