2.6
2.7
length movement.
8. When the cut is completed, the head will retract, the blade will stop and the display window will reset for
the next cut.
9. To cut another job, repeat steps 1 through step 7.
NOTE: To cut multiple pieces, switch to AUTO and follow the automatic procedures.
AUTOMATIC OPERATION
To enter AUTO MODE, the saw vise switch must be in the closed position. Press the AUTO/MAN button, the
red indicator will come on, the screen will change to the PICK LIST display as shown on PAGE 11 and be
ready for editing or starting a new job. The VISE, HEAD and all MANUAL functions on the control panel are
disabled. At this point it is possible to edit an existing job or enter a new job.
PROCEDURE FOR EDITING OR STARTING A NEW JOB IN AUTO MODE
Each job is defined by two angles and two lengths. Angle 1 (A1) is the first angle to be cut (this will be the trim
cut). Length 1 (L1) is the length of the material to be cut as measured between the two intersection points of
the blade axis and the saw table datum line. Angle 2 (A2) is the second angle to be cut and length 2 (L2) again
is the length of material as measured between the two intersection points of the blade axis and the table datum
line.
Summary of Contents for V-18 APC
