13
08/2015
1248867
14. Documentation supplémentaire
Sur demande, vous pouvez obtenir les notices
techniques avec plans en coupe, liste des pièces et
instructions de montage des pièces détachées.
→
Veuillez indiquer le numéro de commande à 16
chiffres ainsi que le numéro de série.
15. Directives des appareils soumis à
pression CE/97/23
Les électrovannes ≤ DN 25 sont conformes à l’ar
ticle 3, paragraphe 3 des directives des appareils
soumis à pression CEE/97/23. Vous pouvez recevoir
sur demande une déclaration de conformité pour
les vannes des catégories I et II.
16. Remarque sur la directive 2004/108/CE
(Compatibilité électromagnétique CEM)
Les électroaimants sont conformes aux exigences
des normes génériques sur les émissions parasites
(EN 6100063) et sur la résistance antiparasite
(EN 6100061).
Les électroaimants sans redresseur de courant
intégré sont aussi conformes aux exigences des
normes EN 6100063. Pour la mise en service,
il faut vérifier que la machine complète ou l’instal
lation soit conforme aux dispositions de la directive
de CEM.
17. Remarque pour electrovannes d‘après les
normes américaines et canadiennes
Si la plaque signalétique de l‘electroaimant est
marquée du signe
c
CSA
us
, cela signifie que les
normes significatives américaines/canadiennes sont
respectées.
→
Recherchez dans la catégorie « service »
sur la page d‘accueil de Buschjost
www.buschjost.com
. Vous y trouverez le
certificat correspondant, avec les éventuelles
différences des conditions d‘utilisation.
→
!
ATTENTION
Utiliséez uniquement pièces de
rechange ou d‘usure originales.
REMARQUE
Evitez autant que possible l‘encras
sement.
11.5 Remontage des composants
1. Montez le composants internes de vanne.
2. Montez le couvercle de boîtier de vanne sur le
boîtier de vanne et vissez en croix à l’aide des vis
à tête cylindrique.
3. Montez le composants de manchon magnétique.
4. Montez et vissez le prémonté manchon magné
tique sur le couvercle de vanne.
5. Montez l’électroaimant.
11.6 Remise en service
→
Remarquez les chapteurs 8 à 10.
12. Mise hors service
Les travaux de mise horse service ne doivent être
effectués que par un personnel qualifié. Pratiquée
tout les mesures de sécurité.
!
AVERTISSEMENT
Tuyauteries sous pression
présenter un risque
Tuyauteries sous pression risquent
d‘exploser et de causer par consé
quent des blessures.
→
Dépressurisez le système tubulaire avant
travailler sur la vanne.
1.
!
DANGER
L’électroaimant doit alors être hors
tension.
2.
!
ATTENTION
Avant toute mise hors service,
dépressurisez le système tubulaire et évacuéz.
3.
!
ATTENTION
Laissez l‘électroaimant refroidir
avant de le toucher et travailler sur la vanne.
4. Retiréz l’électrovanne du système tubulaire.
5. Videz la vanne complètement.
REMARQUE
En cas de matières dangereuses
pour l’eau, il convient de se conformer à la loi
concernant l’utilisation et la protection des eaux.
6. Nettoyez et séchez la vanne.
13. Élimination
1. Retiréz l’électrovanne comme décrit dans le
chapitre «
12
Mise hors service ».
2. Démontéz l’électrovanne afin de retransmettre
les matériaux réutilisables dans le circuit des
matières.