background image

Sprayer Body and Gun Diagram

A

A

B

C

D

E

F

A

B

C

B

U

C

D

E

F

G

H

I

J

K

L

K

G

I

M

N

O

P

Q

R

S

T

Safety and General Maintenance

11

6

CAUTION!

    This machine is an electrical appliance. Care must be taken to reduce 

the risk of electrical shock. 

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING 

•  To reduce the risk of property damage or injury, repairs to electrical systems 

should only be performed by experienced technicians. Contact your dis-

tributor for assistance. Unplug the power cord from the wall outlet before 

performing any repairs.

•  This sprayer shall be grounded while in use to protect the operator from 

electric shock. The sprayer is provided with a three-conductor cord and a 

three-contact grounding type attachment plug to fit the proper grounding 

type receptacle. The green (or green and yellow) conductor in the cord is the 

grounding wire. Never connect this wire to other than the grounding pin of 

the attachment plug.

•  This sprayer is for use on a nominal 120-volt circuit and has a grounding plug 

that resembles the plug illustrated in the sketch below. Make sure that the 

power cord for this sprayer is connected to an outlet with the same configu-

ration as the plug. No plug adapter should be used with this sprayer.

•  The power cord supplied with the AS76 FlexiPro sprayer is properly sized to 

handle the electrical load of the pump and is properly grounded as de-

scribed above. Any extension cords used with this sprayer must be similarly 

sized and grounded to assure safe operation.  A GFCI protected cord or 

outlet can be used for additional protection.

•  Do not use the AS76 FlexiPro sprayer outdoors, in standing water or on wet 

surfaces. Do not store the AS76 FlexiPro sprayer in wet conditions. If sprayer 

is leaking, unplug the power cord from the wall outlet before approaching or 

touching the sprayer. 

•  Do not unplug power cord by pulling on the cord. Grasp the plug end when 

unplugging the cord. Do not pull the FlexiPro sprayer by the cord. If cord 

or plug is damaged, do not use cord. Replace with new cord or repair as 

needed before use.

Summary of Contents for FlexiPro AS76









Reviews: