background image

– Your Authorized Local Distributor –

www.hydromatic.com

STANDARD LIMITED WARRANTY

     

HYDROMATIC

®

 warrants its products against defects in material and workmanship for a period of 12 months 

from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - 

provided that such products are used compliance with the requirements of the Hydromatic catalog and          

technical  manuals  for  use  in  pumping  raw  sewage,  municipal  wastewater  or  similar,  abrasive  free                 

non-corrosive liquids. 

During the warranty period and subject to the conditions set forth, Hydromatic, at its discretion, will repair or 

replace to the original user, the parts which prove defective in materials and workmanship. Hydromatic 

reserves the right to change or improve its products or any portions thereof without being obligated to provide 

such a change or improvement for prior sold and/or shipped units.

Start-up reports and electrical schematics

 may be required to support warranty claims. Warranty is 

effective only if Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be 

hooked up, functional and monitored or this warranty will be void. Hydromatic will only cover the lower seal 

and labor thereof for all dual seal pumps. Under no circumstance will Hydromatic be responsible for the cost 

of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from 

the factory or an authorized Hydromatic service facility.

This limited warranty will not apply:

 (a) to defects or malfunctions resulting from failure to properly 

install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting 

from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such 

service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good 

trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other 

than for what it is designed and manufactured; (g) to any unit which has been repaired or altered by anyone 

other than Hydromatic or an authorized Hydromatic service provider; (h) to any unit which has been repaired 

using non factory specified/OEM parts.

Warranty Exclusions:

 HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES WHICH EXTEND 

BEYOND THE DESCRIPTION ON THE FACE HEREOF. HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.

Liability Limitation:

  IN  NO  EVENT  SHALL  HYDROMATIC  BE  LIABLE  OR  RESPONSIBLE  FOR                    

CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER 

TO ANY HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE 

MAY RESULT FROM IMPROPER INSTALLATION. HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING   

LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. HYDROMATIC RECOMMENDS   

INSTALLATION BY PROFESSIONALS.

Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of              

incidental or consequential damages and therefore such limitations may not apply to you. No warranties          

or  representations  at  any  time  made  by  any  representatives  of  Hydromatic  shall  vary  or  expand  the                 

provision hereof.

USA

740 East 9th Street, Ashland, Ohio 44805

Tel: 419-289-3042  Fax: 419-281-4087

CANADA

269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5

Tel: 519-896-2163  Fax: 519-896-6337

Warranty Rev 02/09

Summary of Contents for Novus 1000 Series













Reviews: