MoniMax 5600T 6. Appendix
6 - 19
2) Receipt Printer
Error Code
Cause
Handling
2010100
In case of detecting to be open lever of
print head before printing receipt paper
1.Close the lever of print head completely
2010200
In case of detecting to be overheated in
print head before printing receipt paper
1.Wait the time until the temperature of head
adequately slow down and try to initialize
2010300
Paper jam occurs in return path before
printing or cutting or discharging receipt
paper
1.Remove jammed paper between printer head and
rollers
2010400
It is detected that paper is empty before
printing receipt printer
1.Replenish receipt paper
2.Check the status of sensor and its connctor
2010500
It is detected that paper is not properly
set before printing
1.Check the status of setting paper
2.Check the status of sensor and its connctor
2010600
Command is received while doing self-
test
1.After terminating self-test and initialize receipt
printer
2010700
Receipt paper runs out of before printing
1.Replenish receipt paper in paper charger
2.Check the status of Near End sensor and its
connctor
2010800
It is detected that paper is not properly
cut while operating
1.Check the Cutter module
2.Check if printer head lever is properly close
2010900
Black mark is not properly detected in
receipt paper before printing
1.Check the status of Black mark sensor
2.Check if Dip switch # 6 is correctly set
(Dip switch # 6 is set by On in case of not using
Black mark)
2010A00
The size of image print data is abnormal
while printing image
1.Check the AP version and initialize
2080100
In case of detecting to be open lever of
print head after printing receipt paper
1.Close the lever of print head completely
2080200
In case of detecting to be overheated in
print head after printing receipt paper
1.Wait the time until the temperature of head
adequately slow down and try to initialize
2080300
Paper jam occurs in return path after
printing or cutting or discharging
receipt paper
1.Remove jammed paper between printer head and
rollers
2080400
It is detected that paper is empty after
printing receipt printer
1.Replenish receipt paper
2.Check the status of sensor and its connctor
2080500
It is detected that paper is not properly
set after printing
1.Check the status of setting paper
2.Check the status of sensor and its connctor
2080600
Command is received while doing self-
test
1.After terminating self-test and initialize receipt
printer
Summary of Contents for MoniMax 5600T
