background image

OTHER CONSIDERATIONS

CLEANING: Take the time on a dry sunny day and wash your 

shelter out, spot-cleaning any areas that need it. A hose with a 

bucket of water and a mild soap (powdered detergent works well, 

do not use bleach) will work on any of our DCF fabrics. Air-dry 

your shelter by either pitching it and leaving it out with the door 

open or hang-dry it. Make sure your shelter is completely dry 

before storage. This will help protect the fabric and keep it safe 

from any damage.

STORAGE: Store your Hyperlite Mountain Gear products in a dry 

place with minimal fluctuation in temperature if possible. 

ONGOING MAINTENANCE/STORAGE: Periodically check 

stake-out points and trekking pole contact areas for signs of 

stress or tears and repair any damage before continued use.

MANUFACTURER’S WARRANTY: If one of our products fails 

due to a manufacturer's defect within one year, the original 

purchaser may return it to us for repair, replacement or refund of 

the original purchase price at our discretion. This warranty 

protects the original owner against manufacturing defects in 

workmanship and materials. Damage due to wear and tear, 

accident, improper use, negligence, or the natural breakdown of 

materials over extended time and use is not covered.

RETURN POLICY: If you are not satisfied with a product 

purchased directly from Hyperlite Mountain Gear at the time you 

receive it, you may return it, unused, for a refund of your purchase 

price, within 15 days.

REPAIR POLICY: Contact us a 800.464.9208 with any questions 

about repairs to our gear. We’re always happy to help.

Summary of Contents for ULTAMID

















Reviews: