Changed Page
Description
IM246 Rev 11 to 12
4/10/00
0.02
Replaced text from "to Hypertherm's place of business..." to "to an authorized Hypertherm repair facility..."
4.14
Added remote power on/off signals to machine interface cable
6.13
Added p/ns for retaining cap with IHS tab
8.20
New graphic of chopper
9.08
Added graphic of relays to Fig. 9-4
9.09
Added part numbers for relays
9.21
Changed p/n of PS3 from 005130 to 005227
9.51
Changed p/n of PS3 from 005130 to 005227
10.05-10.13
Uprevved wiring diagrams to RZ
Begin w/serial # 2000-005756
Changed Page
Description
IM246 Rev 10 to 11
9/27/99
0.01
Uprevved because of ECNs 10483, 10484, 10639, 10145, 10670
0.02
Added plumbing and electrical codes statement to warranty
0.04
Updated TOC for added section on cutting techniques, beveling consumable parts kit
0.05
Updated TOC for added section on cutting techniques, beveling consumable parts kit
0.08
Updated TOC for added section on cutting techniques, beveling consumable parts kit
1.0-1a.06
New safety sections
3.02
Bolded installation by qualified...; rewrote hard plumbing suggestions
3.03
Bumped page
3.04
Bumped page
6.01
Updated TOC for added section on cutting techniques
6.12
Referenced new section on cutting technique
6.39-6.42
New section on cutting techniques
8.25
Changed graphic of coolant reservoir
8.26
New graphic of coolant reservoir
9.01
Updated TOC for beveling consumable parts kit
9.17
Corrected part no. of adapter from 015157 to 015015
9.18
New coolant reservoir
9.19
New coolant reservoir #, new level switch SA #
9.25
New part number for pressure switches
9.36
New figure of torches
9.37
New torch mounting sleeve #
9.48
Renamed 1st header from consumable parts kit to HT2000 Consumable Parts Kit
9.49
Added HT2000 Beveling Consumable Parts Kit
9.51
Updated power supply recommended spare parts to include new level switch #
9.52
Updated gas console recommended spare parts to include new pressure switches
10.05-10.13
Uprevved wiring diagrams to RX
Begin w/serial # 2000-005600
Begin w/serial # 2000-006387
Changed Page
Description
IM246 Rev 12 to 13
8/31/03
9.4 & 9.5
Item # 5 changed from 041590 to 041762. Item # 6 081039 (firmware) was removed. Item
numbers following Item #5 changed to agree.
Section 10
Wiring diagrams Revision change from RZ to SC
Summary of Contents for HT2000
