Changed Page
Description
IM246 Rev 5 to 6
1/15/98
0.01
Uprevved because of IOP, ECNs 8912, 8910, 9035, 8746
0.04
Updated TOC
0.06
Updated TOC
4.04
Added torque spec.
4.16
Removed current 400 signal from cable description
6.01
Changed TOC
6.03
Added note to hold down on button for up to 1 minute
6.10
Added note to hold down on button until leds extinguish
6.12
Added note to begin and end cut on plate
6.13
Renumbered pages on cut chart index
6.14-6.15
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.16
Added initial torch piercing height to cut charts
6.17-6.18
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.19
Added initial torch piercing height to cut charts
6.20-6.22
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.23
Added initial torch piercing height to cut charts
6.24
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.25-6.26
Added initial torch piercing height to cut charts
6.27-6.29
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.30
Added initial torch piercing height to cut charts
6.31
Added initial torch piercing height to cut charts; combined under+above water on 1 page
6.32-6.34
Added initial torch piercing height to cut charts
6.35
Put all gouging cut charts on 1 page
6.36
Bumped page
6.37
Bumped page; better graphic of main body; removed reference to nozzle o-ring
6.38
Bumped page
8.03
(from)...status LED turn off... (to)...status LED illuminate
8.10
Edited for easier translation
8.11
Edited for easier translation
8.12
Edited for easier translation
8.13
Edited for easier translation
8.14
Edited for easier translation
8.16
Edited for easier translation
8.17
Edited for easier translation
8.18
Edited for easier translation
9.04
New graphic of front panel
9.05
New part numbers for fans - added fan guard; new graphic of THC
9.11
Fuseholder p/n change
9.15
4 ohm resistor p/n change, designation change
9.51
Designation updates in recommended spare parts; added flowswitch
9.52
Added 100 psi pressure gauge to gas console recommended spare parts
10.01
Uprevved wiring diagrams to
10.02
(from) 2 of 9 in the...(to)...2 in the...
e.04
Added spacer to graphic of power supply
e.06
Added spacer and part number to power supply
i.01 to i.06
Updated index
Begin w/serial # 2000-004270
Summary of Contents for HT2000
