9
OPERATION
4-12
HySpeed HT2000LHF
Instruction Manual
Shield
Arc
Approx.
Material
Plasma Gas Flow Rate %
Gas (Air)
Torch-to-work
Initial Torch
Voltage
Motion
Thickness
Preflow
Cutflow
Pressure
Distance
Piercing Height
Setting
Travel Speed
Delay Time
(inches)
(mm)
(O
2
% N
2
%) (O
2
% N
2
%)
(psi)
(inches)
(mm)
(inches)
(mm)
(volts)
(ipm) (mm/min.)
(sec)
Shield
Arc
Approx.
Material
Plasma Gas Flow Rate %
Gas (Air)
Torch-to-work
Initial Torch
Voltage
Motion
Thickness
Preflow
Cutflow
Pressure
Distance
Piercing Height
Setting
Travel Speed
Delay Time
(inches)
(mm)
(O
2
% N
2
%) (O
2
% N
2
%)
(psi)
(inches)
(mm)
(inches)
(mm)
(volts)
(ipm) (mm/min.)
(sec)
1/4
6
12
38
76
0
60
1/16
1.5
1/8
3
145
230
5800
0.3
5/16
8
(12 / 50
(90 / 0
(275
1/8
3
1/4
6
151
165
4200
0.3
3/8
10
SCFH)
SCFH)
SCFH)
5/32
4
5/16
8
155
140
3500
0.3
1/2
12
1/8
3
1/4
6
155
120
3000
0.3
5/8
15
1/8
3
1/4
6
155
100
2500
0.5
3/4
20
1/8
3
1/4
6
155
75
1900
0.6
7/8
22
1/8
3
1/4
6
159
60
1500
0.7
1
25
1/8
3
1/4
6
160
50
1300
0.7
1 1/4
32
1/8
3
5/16
8
168
30
760
2.6
1-1/2
38
1/8
3
5/16
8
175
20
500
4.0
1-3/4
44
1/8
3
N/A
N/A
180
15
380
N/A
2
50
1/8
3
N/A
N/A
188
10
250
N/A
Mild Steel
HySpeed 200 amps • O
2
Plasma / Air Shield
This gas combination gives superior cut speed, minimum dross, minimum surface nitriding and excellent
weldability.
Notes:
Set oxygen plasma gas inlet pressure to 120 psi (8.3 bar).
Set nitrogen plasma gas inlet pressure to 120 psi (8.3 bar)
Set shield gas inlet pressure to 90 psi (6.2 bar)
Production cutting above 1" (25 mm) not recommended.
Drop cutting above 1-1/2" (38 mm) not recommended
Above Water
1/4
6
12
38
76
0
60
1/16
1.5
1/8
3
149
230
5800
0.3
5/16
8
(12 / 50
(90 / 0
(275
1/8
3
1/4
6
151
165
4200
0.3
3/8
10
SCFH)
SCFH)
SCFH)
5/32
4
5/16
8
159
140
3500
0.3
1/2
12
1/8
3
1/4
6
155
105
2700
0.3
5/8
15
1/8
3
1/4
6
161
90
2300
0.5
3/4
20
1/8
3
1/4
6
161
65
1600
0.6
7/8
22
1/8
3
1/4
6
161
55
1400
0.7
1
25
1/8
3
1/4
6
164
45
1100
0.7
3" Under Water
220235
Electrode
220237
Nozzle
220242
(cw)
220243
(ccw)
Retaining cap
220239
Shield
220236
(cw)
220244
(ccw)
Swirl ring
Summary of Contents for HT2000LHF
