Installation
‐
Checking
for
Shipping
Damage
15
5.2.6
Proximity
to
the
Plasma
Cutting
System
The
Hypertherm
HPR800XD
plasma
cutting
system
is
supplied
with
a
standard
hose
kit
for
connecting
the
process
cooling
circuit
water
from
the
chiller
to
the
plasma
cutting
system.
The
chiller
location
must
be
close
enough
to
the
plasma
cutting
system
to
enable
connectivity
with
the
standard
hose
kit.
CAUTION
Exceeding
the
standard
hose
lengths
can
cause
excessive
pressure
drop
through
plumbing
systems
that
leads
to
chiller
flow
faults
and/or
premature
chiller
pump
failures.
6
Installation
6.1
Checking
for
Shipping
Damage
Upon
delivery
of
the
chiller
always
verify
that
the
shipment
matches
the
bill
of
lading.
Inspect
the
chiller
immediately
for
signs
of
shipping
damage
both
visible
and
concealed.
Damaged
crating
indicates
likely
damage
to
the
chiller
and
may
require
the
removal
of
the
panel
and/or
air
filter(s)
for
further
inspection.
Refer
to
section
6.4
Internal
Access
to
remove
the
panel
or
air
filter(s)
of
the
chiller.
Any
damage
must
be
reported
to
the
shipping
carrier
and
a
copy
of
the
damage
claim
submitted
to
GDTS
or
your
sales
representative.
6.2
Transportation
The
chiller
is
shipped
in
a
crate
with
protective
packing
and
wrapping
that
should
remain
in
place
until
the
unit
is
transported
to
its
final
installation
location.
It
is
recommended
that
the
chiller
(crated
or
uncrated)
be
moved
with
a
forklift.
WARNING
The
chiller
is
heavy
and
there
is
risk
of
tilting
or
falling
when
moved.
Transportation
of
the
chiller
must
only
be
performed
by
trained
and
qualified
personnel
using
appropriate
equipment.
Ensure
that
the
chiller
is
securely
positioned
(tines
of
forklift
spread
as
far
as
permitted
along
the
chiller’s
long
edge
and
extend
thoroughly
through
the
opposite
lifting
face)
before
moving
the
chiller.
Improper
handling
or
insecure
lifting
of
the
chiller
during
transportation
can
cause
it
to
tip
and
fall
leading
to
injury
or
death.
WARNING
The
chiller
is
only
intended
to
be
lifted
from
the
sides
(filter
or
door).
Lifting
the
chiller
from
the
ends
(Electrical
enclosure
or
plumbing
I/O)
can
cause
it
to
tip
and
fall
leading
to
injury
or
death.
Hypertherm, Inc. Part Number: 810540
Summary of Contents for Koolant Koolers N-Series
