B W
MILLER EDGE
GEM
CONNECT TO GATE EDGE
WITH 10K OHM RESISTOR
PHOTO EYE
TRANSMITTER
+ 24
VDC
COMMON / NEG.
PHOTO EYE
RECEIVER
+ 24
VDC
COMMON RELA
Y
NC RELA
Y
SENSOR C
OM / NEG.
B W
MILLER EDGE
GEM
STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
SENSOR 1
SENSOR
COM
DO NOT USE
SENSOR 2
DO NOT USE
SENSOR 3
DO NOT USE
CHARGER
AC LOSS
LOCK INTERLOCK
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT
DUAL GATE
RADIO OPTIONS
DRIVE
POWER
RS485
MO
TO
R
U
SER 1
USER 2
USER 3
VEHICLE DETE
C
TOR
VEHICLE DETE
C
TOR
VEHICLE DETE
C
TOR
ST
OP
/BUZZER
FREE
EXIT
INSIDE
OBS
TR
OUT
SIDE
OBS
TR
SHADO
W
RE
SET
WIE
G
AND
Hy
Security
COM
NO
MX000585
VERSION
S/N
R
S232
DISPLA
Y
VEHICLE DETE
C
TOR
COM
COM
A
B
RPM
COM
OPEN
S 1
+24V
+24V
STATUS
LED
S2 0
SENSOR #2 TYPE
S2 6 (EDGE BOTH)
SENSOR #2 TYPE
S1 0
SENSOR #1 TYPE
S1 4 (EYE OPEN)
SENSOR #1 TYPE
S3 0
SENSOR #3 TYPE
S3 6 (EDGE BOTH)
SENSOR #3 TYPE
All three sensor inputs must be
CONÚGURED
An example of the connections for an Edge and a Photo Eye (monitored “sensors”) and the Installer Menu settings for
the Smart Touch Controller (STC) are shown in Diagram 4. The wiring in Diagram 4 shows a generic photo eye. For wiring
SPECIÚCTO(Y3ECURITYAPPROVEDSENSORSSEE7IRING$IAGRAMSONPAGE
Smart DC Controller (SDC) inputs are similar to the STC). See table on page 7. The SDC has a different display, but
needs to be programmed in a similar fashion as the STC. An example of a site overview for the SwingSmart DC is shown
on page 15.
NOTE:
9OURSITEREQUIREMENTSMAYDIFFERFROM$IAGRAMØTMINIMUMMONITOREDEXTERNALENTRAPMENTPROTECTIONSENSORSMUST
be used to protect both open and close directions of gate travel.
D
IAGRAM
4: S
WING
R
ISER
I
NPUTS
& P
ROGRAMMING
NOTE:
ØSEPARATE'%-ISREQUIREDFOREACHEDGESENSOR)FYOUHAVEFOREXAMPLE
TWOEDGESENSORSYOUWILLNEEDA'%-WIREDTOEACHEDGESENSORANDEACH'%-
MUSTBEWIREDTOTHE#ONTROLLER3ETTHE3%.3/2TYPESINTHE)NSTALLER-ENUACCORDINGLY
Green
wires
Red wires
Smart Touch Programming Sequence
based on site scenario, page 15.
SENSOR 1
Default = 0
Program
SENSOR
1 to Photo
EYE OPEN
direction
Program
SENSOR 2
to contact
EDGE BOTH
directions
SENSOR 2
Default = 0
SENSOR 3
Default = 0
Program
SENSOR 3
to contact
EDGE BOTH
directions
16
D0726 Rev. C
UL 325 - 2016 HySecurity Monitored Sensors
©
2016 www.hysecurity.com
Summary of Contents for UL 325-2016
Page 33: ...Page intentionally left blank...
Page 34: ...Page intentionally left blank...
