Hyster G001, Repair Manual

Figure 13. Inner Oil Seal Installation

NOTE:   

To  prevent  damage  to  inner  oil  seal  when

installing hub, hub and drum assembly can be tem-
porarily fastened to the wheel. Align height of axle
housing with hub bearings. Put grease under wheel
and slide wheel toward axle housing.

18. 

Install  outer  bearing  and  nut,  for  lift  truck
models

• S30-35FT, S40FTS (F010)
• H1.6-1.8FT, 

H2.0FTS 

(H30-35FT,

H40FTS) (G001)

• S2.0-3.5FT (S40-70FT, S55FTS (H187)
• H2.0-3.5FT (H40-70FT) (P177)

Install  wear  sleeve,  inner  seal,  inner  bearing,
outer  seal,  roller  bearing  and  nut,  for  lift  truck
models (see Figure 3)

• S50CT (B267)
• H2.0-2.5CT (H50CT) (B274)

19. 

Install  washer,  lock  plate  and  wheel  adjust-
ment nut for lift truck models

• S30-35FT, S40FTS (F010)
• H1.6-1.8FT, 

H2.0FTS 

(H30-35FT,

H40FTS) (G001)

• S2.0-3.5FT (S40-70FT, S55FTS (H187)
• H2.0-3.5FT (H40-70FT) (P177)

Install  lockwasher,  locknut  and  wheel  adjust-
ment nut for lift truck models

• S50CT (B267)
• H2.0-2.5CT (H50CT) (B274)

NOTE:  

Perform steps Step a through Step f for all

lift truck models.

a. 

To  align  bearing  rollers,  tighten  wheel  ad-
justment  nut  to  14  to  18  N•m  (124  to
159  lbf  in)  and  rotate  hub  2  revolutions  in
both directions.

b. 

To seat wheel bearings, tighten wheel adjust-
ment  nut  to  175  to  215  N•m  (129  to
159 lbf ft) for lift truck models

• S2.0-3.5FT 

(S40-70FT, 

S55FTS)

(H187)

• H2.0-3.5FT (H40-70FT) (P177)

c. 

To seat wheel bearings, tighten wheel adjust-
ment nut to 120 to 145 N•m (89 to 107 lbf ft)
for lift truck models

• S30-35FT, S40FTS (F010)
• H1.6-1.8FT,  H2.0FTS  (H30-35FT,

H40FTS) (G001)

• S50CT (B267)
• H2.0-2.5CT (H50CT) (B274)

d. 

Back  off  wheel  adjustment  nut  to  zero  end
play.

e. 

Preload  wheel  bearings  by  tightening  wheel
adjustment  nut  to  14  to  18  N•m  (124  to
159  lbf  in).  Rotate  hub  3  complete  revolu-
tions in both directions.

f. 

Verify wheel adjustment nut torque is 14 to
18  N•m  (124  to  159  lbf  in)  and  that  torque
stabilizes at that specification.

20. 

Bend lock plate over lock nut. See Figure 14, for
lift truck models

• S30-35FT, S40FTS (F010)
• H1.6-1.8FT, 

H2.0FTS 

(H30-35FT,

H40FTS) (G001)

• S2.0-3.5FT (S40-70FT, S55FTS (H187)
• H2.0-3.5FT (H40-70FT) (P177)

.

Bend bearing lockwasher over lock nut. See Fig-
ure 3 for lift truck models

• S50CT (B267)
• H2.0-2.5CT (H50CT) (B274)

.

Service Brakes Repair (Dry Brake)

1800 SRM 1743

16