background image

                                                                                                                               

TC-446S Owner

’s Manual 

 

 

13 

Basic Operations

 

Turning the Radio On/Off 

Rotate the 

Radio On-Off/Volume Control

 knob clockwise/counter-clockwise until a click is heard to turn 

the radio on/off.   

 

Adjusting the Volume 

You  may  control  the  volume  level  using  the 

Radio  On-Off/Volume  Control

  knob.  After  the  radio  is 

powered  on,  rotate  the  knob  clockwise  to  increase  the  volume,  or  counter-clockwise  to  decrease  the 

volume.   

 

Selecting a Channel   

The radio supports up to 16 channels. Rotate the 

Channel Selector 

knob to align your desired channel 

number with the white channel mark.   

  Note: 

When  the  radio  is  currently  staying  on  a  blank  channel,  it  would  sound  beep  tones 

continuously.   

 

Transmitting/Receiving   

To  transmit  audio  signals,  press  and  hold  down  the

  PTT

,  and  speak  into  the  microphone.  During 

transmitting, the LED solidly glows red.   

To receive, just release the 

PTT

. When any audio signal is received, the LED solidly glows green.   

  Note:   

  To  ensure  optimal  volume  of  the  receiving  radio,  hold  the  radio  approximately  2.5  to  5 

centimeters away from your mouth.   

  Communication range may get affected in rainy days or forest locations.   

 

Summary of Contents for TC-446S






















Reviews: