background image

                                                                                                                               

TC-446S Owner

’s Manual 

 

 

20 

Care and Cleaning 

 

 

To guarantee optimal performance as well as a long service life of your product, please follow the tips 

below.   

 

Product Care   

 

Do not pierce or scrape the product with any edged instruments or hard objects.   

  Keep the product far away from substances that can corrode the electronic circuit.   

 

Do not hold the product by its antenna or headset cable directly.   

 

Attach the accessory jack cover when the product is not in use.   

 

Product Cleaning   

 

Clean up the dust and fine particles on the product surface and charging piece with a clean and dry 

lint-free cloth or a brush regularly.   

 

Use neutral cleanser and a non-woven cloth to clean the keys, control knobs and front case after 

long-time  use.  Do  not  use  chemical  preparations  such  as  stain  removers,  alcohol,  sprays  or  oil 

preparations, so as to avoid surface case damage. Make sure the product is completely dry before 

use.   

 

Caution:

 Power off and remove the battery before cleaning.   

 

 

Summary of Contents for TC-446S






















Reviews: