background image

SPECIFICATIONS

•  E24i™  Motor  with  Integrated  Card 

Requirements

Power Requirements

Power In

• 

24.0 VDC nominal @ 1.5 A maximum

Normal operation from 22.0 – 28.0 VDC

 

Will allow operation above 28.0 VDC but control will get hotter.

 

Will allow operation below 22.0 VDC but full speed will be 

 

unattainable.

29.0 + 0.2 VDC over-voltage detection (unit will cease normal 

operation)

19.0 + 0.2 VDC under-voltage detection (unit will cease normal 

operation)

Polarity protection is provided

Note that the control’s ground does not attach to the metal 

 

chassis; doing so assures a solid ground but then if the power 

supply is reversed it’s positive output

Fuse non-replaceable 5 AMP. Fuse located under the cover.

PNP Inputs

• 

PNP Input Signal Levels

Active when pulled up above 18.0 VDC

 

Need to be able to source 3 mA

 

Two input signals

Motor Run

 

Motor Reverse

 

Analog Speed Input

• 

Allow the speed to be controlled from a single point

 

Voltage range: 0-10 VDC

 

Minimum impedence presented to input: 5K

 

PNP Output

• 

Signal Levels

Sources current when active

 

Maximum current for this unprotected output is 50mA.

 

A 150Ω series resistor helps the PNP output limit current draw 

 

for most situations; voltage out is thus lower as current draw 

increases.

Voltage dependent on input power and current draw.

 

One output signal

Motor Running

 

    

Environmental Requirements

Temperature

• 

The unit shall operate within specified limits over the range of -20 to 

40 °C (-4 to 120 °F).

The unit can be stored in the range of -40 to 85 °C (-40 to 185 °F).

Humidity

• 

The unit shall operate within specified limits in relative humidity in the 

range of 20 to 90% (non-condensing).

The unit can be stored in the range of 5 to 95% (non-condensing).

 

    Safety – Unintended Use Considerations

Installer

• 

This product is intended for installation by qualified personnel only; 

although of relatively low voltage there are dangerous levels of current 

controlled on the board that are not protected from misplaced fingers.

Note that the cover makes it difficult to touch any power.

 

A tool will be required to move the DIP switches; a plastic-tip 

 

screwdriver is recommended.

User

• 

Product shall be located away from the user such that touching of the 

control is not possible.

MAINTENANCE

• EZLogic® System

EzLogic® Accumulation System Connections

The Model 190-E24Ez is equipped with the EzLogic® Accumulation System.  The 

following  basic  information  may  be  used  as  a  guide  during  the  installation  and 

initial  setup  of  the  conveyor.    For  detailed  information  about  EzLogic®  system 

components, options, functions, and programming, please refer to the EzLogic® 

GEN3 Component Manual. 

Each  EzLogic®  zone  controller  is  equipped  with  sealed  connectors  for  zone-to-

zone  communication,  solenoid  output,  and  zone  stop  connections  (Figure  7A).  

These connections are described in the following sections.

ZONE CONNECTIONS

Each zone has a cordset terminated with a female micro-connector and a male 

micro-connector.  This cordset provides power to all the controllers on the conveyor 

as well as communication between controllers.  All controllers are mounted and 

connected  at  the  factory  within  each  conveyor  section.    Connections  between 

sections are made at installation.  (See Conveyor Set-Up, page 4).  The cordset 

from one controller is always connected to the cordset on the upstream side of it.  

This is the way the controllers know which direction product is flowing.  The cordset 

on the infeed end of the conveyor is simply bundled and tied in the accumulation 

channel and is not connected.  The infeed cordset may be replaced with an infeed 

zone  terminator  (P/N  032.550).    Protective  caps  are  provided  to  seal  unused 

connectors.

An optional conveyor-to-conveyor connector is required when two conveyors are 

joined  end-to-end.    Please  refer  to  the  EzLogic®  GEN3  Component  Manual  for 

more information.  

6 1/2 

ZONE LENGTH

Zone Controller

Cordset 

Wiring Harness W/Drops

Wiring Harness W/Drops

6 1/2

Unidrive Motor

Figure 6B

• E24 Connections

Figure 6A

• E24EZ Connections

6

Summary of Contents for 190-E24





















Reviews: