background image

15

layer of oil to the outside of the cartridge filter with a brush (you can use clean engine oil

for this). Insert the filter cartridge into its housing and replace the air box lid, ensuring that

each component is in place and properly installed. If the filter cartridge is damaged or is

very dirty, replace it using a genuine part.

WARNING: Do not twist the cartridge to clean foam, as you could damage it. This mower

is equipped with a dual filtration system comprising a foam pre

filter and a cartridge filter

paper.
Themaintenanceofafoampre

filterisidenticaltothatofafoamcartridgefilter,as

described above. The cartridge filter paper should be cleaned with a vacuum cleaner. If it

is dirty or contaminated with oil or petrol, replace it.

Clean the cover and inside of the air box with a clean cloth. Evenly apply a thin layer of oil

to the outside of the cartridge filter with a brush (you can use clean engine oil for this).

Replace the filter cartridge in its housing and then replace the lid of the air box, ensuring

that each component is in place and properly installed.

Adjusting the transmission cable

In its transmission

engaged position, the mower’s advance lever is pushed fully towards

the handlebar. An incorrectly

adjusted transmission cable can cause premature wear to

the mower’s drive system.

If the transmission cable is too tight, it will be difficult to move the advance lever towards

the handlebars. Conversely, if the transmission cable is not tight enough, the transmission

will function poorly and will lack power.

To adjust the tension of the cable transmission, increase or reduce the length of the

adjustment device using the key. Check the effectiveness of the transmission and the

resistance of the lever.

Once proper adjustment has been reached, secure the adjustment device by tightening

the lock nuts.

Warranty

We guarantee this product for 2 full years.

The warranty period for this item starts on the day of purchase. You can prove the date of purchase

by sending us the original receipt.

We insure over the entire warranty period:

Free repair of possible malfunctions.

Free replacement of damaged parts.

Including the free service of our specialized personnel (i.e. free assembly by our technicians)

Provided that the damage is not due to improper use of the device.

To help you with your product, we invite you to use this link or call us on +33 (0)9 70 75 30 30:

https://services.swap-europe.com/contact

You must create a "ticket" via their platform:

• Register or create your account

• Indicate the reference of the tool

• Choose the subject of your request

• Explain your problem

• Attach these files: Invoice or receipt, identification plate photo (serial number), photo of the

part you need (eg broken transformer plug pins)

Summary of Contents for HTDT46-2


















Reviews: