background image

4.

MAINTENANCE

4.1. 

Maintenance schedule.

 

Proper maintenance is not only the basis of safe, economical and easy way of generator operation, 

but also helpful to reduce the air pollution.

 

If these maintenance instructions are not followed properly, it may cause serious personal injury. 

Maintenance period 

Item 

Process 

Each use 

After 1

st

 month or 

20 hours 

Every 3 months or 

100 hours 

Oil 

Check 

Replace 

Air filter element 

Check 

Clean 

Battery 

Check 

Oil filter 

Check 

Replace 

Fuel filter 

Replace 

Fuel pipes 

Check 

Check every 2 years - replace as required 

4.2. 

Oil change. DO NOT dispose of oil down any drains or directly onto the land. You should send 

your used oil to your local recycling centre. 

It is best to drain the engine of all whilst the engine is still warm – DO NOT attempt to drain HOT 

engine oil. 

4.2.1.  Prepare a container to collect used oil and place it under the oil drain pipe. 

4.2.2.  Undo the oil filler cap. 

4.2.3.  Undo the nut of the end of the oil drain pipe and allow all of the used engine oil to drain into 

the oil container. 

4.2.4.  Once all oil has been drained you MUST securely replace the nut at the end of the oil drain 

pipe. 

4.2.5.  To access the oil filler cap remove the cover on the top of the machine. Use an oil filler jug 

and fill with oil SAE15W40 - From empty the machine can hold 2.25 litres of oil.

 Once full replace the filler cap 

securely.

 

Page 12

First issue - 22nd November 2016

Summary of Contents for DHY12500SE

























Reviews: