Hyundai HiE-S SG Series Installation Manual Download

Page: 12 / 13

www.hyundai-es.co.kr

Page 12 of 13

Sales Office

4th Fl., First Tower,
55, Bundang-ro, Bundang-gu,
Seongnam-si, Gyeonggi-do,
13591 Korea

Factory

313, Soi-ro, Soi-myeon, Eumseong-gun,
Chungcheongbuk-do 369-872, Korea

Appendix 1) Module Installation Instruction

(Front / Back Design Load, Safety factor = 1.5)

Method

Overlap of Clamp with Al frame

: 8-10mm

Overlap of Clamp with Al frame

: 9-11mm

Bolting

4 Bolts : 1600/1600 Pa
8 Bolts : 3600/1600 Pa

Clamping

:Clamping area

※

Min. Clamp

Width: 50mm

Long Bar

A: 330

50mm

3600/1600Pa or 2400/2400 Pa

A: 330

50mm

Design load 2400/2400Pa

A: 330

50mm, B: 971

50mm

Design load 3600/1600Pa

Note 1) Certified by

TUV-NORD

2) The Mounting method has been qualified by HES, and the mechanical load tests are based on

IEC61215 ed.2.

Summary of Contents for HiE-S SG Series














Search results

Summary of Contents for HiE-S SG Series

Reviews:

Related manuals for HiE-S SG Series

Brands by name

Popular brands

Hyundai HiE-S SG Series, Installation Manual

Search results

Summary of Contents for HiE-S SG Series

Reviews:

Related manuals for HiE-S SG Series

Brands by name

Popular brands