Hyundai HTT50-A Original Instructions Manual Download

Page: 12 / 16

6. DECLARATION OF CONFORMITY

BUILDER SAS

ZI, 32 rue Aristide Bergès – 31270 Cugnaux - France

Declares that the machinery designated below:

PETROL EARTH AUGER

Ref

：

HTT50-A1

Serial number: 20220674774-20220675073

Complies with the provisions of the Directive “ machinery ” 2006/42/EC and national

laws transposing it:

Also complies with the provisions of the following European directives:

EMC Directive 2014/30/EU

ROHS Directive (EU)2015/863 amending 2011/65/EU

Emission directive (EU) 2016/1628 & 2018/989/EU

Directive on environmental noise emissions from equipment intended for use outside

buildings 2000/14 /EC and 2005/88/EC)

Also complies with European standards, with national standards and the following

technical provisions:

PPP 58068A :2013

AfPS GS 2019:01 PAK

EK9-BE-98(v2):2020

EN ISO 14982:2009

Cugnaux, 17/05/2022

Philippe MARIE / CEO

Summary of Contents for HTT50-A

















Search results

Summary of Contents for HTT50-A

Reviews:

Related manuals for HTT50-A

Brands by name

Popular brands

Hyundai HTT50-A, Original Instructions Manual

Search results

Summary of Contents for HTT50-A

Reviews:

Related manuals for HTT50-A

Brands by name

Popular brands