background image

11. RECYCLING & PRODUCT

DISPOSAL

11.1.  We do not offer a takeback scheme 

for the recovery of Waste Electrical Electronic 

Equipment (WEEE) & Batteries instead the 

responsibility to dispose of WEEE and or 

Batteries is passed onto you by us. So when it 

becomes necessary to dispose of your   

machine you must take it to your local Civic 

Amenity Site. For further information please 

contact your Local Authority for disposal 

advice. 
11.2.  You MUST make sure that all unused 

oil and fuel is disposed of correctly either 

beforehand or at your local Civic Amenity Site. 

Under NO circumstance must any oil and fuel 

be put down any drains. 
11.3.  Waste Electrical Electronic Equipment 

(WEEE) recycling. 
11.3

.1. 

Certain products contain WEEE waste 

which should not be disposed of in your 

domestic waste. 

11.3.2.  You MUST recycle WEEE in accordance 

with your local authority or recycling centre. 
11.4.  Battery recycling, certain products 

contain batteries which should not be 

disposed of in your domestic waste. 

11.4.1.  You MUST recycle batteries in 

accordance with your local authority or 

recycling centre. 
11.5.  Unwanted packaging materials should 

be sorted and taken to a recycling centre so it 

can be disposed of in a manner which is 

compatible with the environment. 
11.6.  The following symbol means that you 

should ‘Reduce – Reuse – Recycle’. 

11.7.  We are a Member of the VALPAK 

National Compliance scheme and our 

registration number is RM08660 
11.8.  For further information about disposal 

please contact your Local Authority. 
11.9.  You can also get more advice and 

guidance about recycling at the following 

website http://www.recycle-more.co.uk 

11.10.  Should you pass this product onto 

another user either sold or loaned you MUST 

pass on this user manual. This will make sure 

that all other users can use and maintain the 

machine safely. 

12. CONTACT DETAILS

POSTAL ADDRESS 
Genpower Ltd, Isaac Way, London Road, 
Pembroke Dock, Pembrokeshire, SA72 4RW. 

UK. 
TELEPHONE 
+44 (0) 1646 687880
FAX
+44 (0) 1646 686198
TECHNICAL E-MAIL
service@genpower.co.uk
WEBSITE www.hyundaipowerequipment.co.uk

13. MANUAL UPDATES

13.1. Our manuals are constantly being 

reviewed and updated. Should you find an 

error, omission or something you find unclear 

please contact your dealer for assistance. 

E&OE. 
13.2. Our latest manuals are also placed 

online. 
1

3

.3. We reserve the right to make any 

modifications without prior notice whenever 

necessary.

Page 32

Summary of Contents for HYBC5080AV





































Reviews: