background image

©I.CH Motion® 2020

 

                                                 

ichmo

.com

 

Specifications subject to change without notice.

 

Owner's Guide: 3P20M Hybrid Stepper Motor Driver

 

Page 9

TECHNICAL DOCUMENT

 

 

Selecting Supply Voltage:

 

 

The  power  MOSFETS  inside  the  3L583M  can  actually  operate  within  +18

50VDC,  including  power  input  fluctuation  and  back  EMF  voltage 

generated  by  motor  coils  during  motor  shaft  deceleration.  Higher  supply  voltage  can  increase  motor  torque  at  higher  speeds,  thus  helpful  for 
avoiding losing steps. However, higher voltage may cause bigger motor vibration at lower speed, and it may also cause over-voltage protection or 
even driver damage. Therefore, it is suggested to choose only sufficiently high supply voltage for intended applications, and it is suggested to use 
power supplies with theoretical output voltage of +24

+ 45V, leaving room for power fluctuation and back-EMF.

 

 
 

9. Output Current and Microstep Resolution Settings

 

 

Current Setting

 

 

For a given motor, higher driver current will make the motor output more torque, but at the same time causes more heating in the motor and 
driver. Therefore, output current is generally set to be such that the motor will not overheat for long time operation. Phase current rating supplied 
by motor manufacturer is important in selecting driver current, however the selection also depends on leads and connections.

 

 

DIP Setting for Dynamic Current

 

 

The 3P20M uses an 8-bit DIP switch to set motor dynamic current, standstill current and microstep resolution, as shown below:

 

 
 
 
 
 

The first four bits (SW1, 2, 3, 4) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor’s required current.

 

 

Peak current (A)

 

RMS (A)

 

SW1

 

SW2

 

SW3

 

2.1

 

1.5

 

OFF

 

OFF

 

OFF

 

2.5

 

1.8

 

ON

 

OFF

 

OFF

 

2.9

 

2.1

 

OFF

 

ON

 

OFF

 

3.2

 

2.3

 

ON

 

ON

 

OFF

 

 
 
 
 
 
 
 
 

Summary of Contents for 3P20M















Reviews: