background image

                                                                        3 

                          

SPECIFICATIONS 

 

Rated capacity  ………………………………4000kg/8800lbs 
Starting pad height (notch) ……………... 65mm/2-1/2inches 
Raised height

—maximum………………….406mm/16inches 

Width………………………………………200mm/7-4/5inches 
Weight………………………………………….…….33kg/77lbs 
 

 
 
 

             

        

 
 

              IMPORTANT: 

Owner and/or Operator Responsibilities: 

1. 

The use of this jack is subject to certain hazards that  can  only 

precluded by the exercise of intelligence, care and common sense. It 
is  therefore  essential  to  have  competent  and  careful  personnel 
involved in the use and operation of this equipment. 
Before  using  the  jack,  you  must  read  and  understand  all  the 
instructions,  warnings  and  precautions  contained  in  this  manual  as 
well those affixed to the jack in the form of decals. 
 

2. 

Warning symbol: 

  

 

This symbol is used to warn you of 

specific    situations  which  may 
occur  and  must  be  avoided  when 
using  the 

HFJ-400

  jack.  Failure  to 

observe these warnings may result 
in  personal  injury  and/or  property 
damage. 
 

WARNING

www.dominga.lt/krautuvai mob. tel.: +370 686 61770 tel.: +370 5 2432146 el. paštas: pakrovejai@dominga.lt

Summary of Contents for HFJ-400















Reviews: