background image

page 19

2.6.6. Counter

Displays a list of counters of the selected OABR switch. The lists can be updated via the Refresh 

button. The counters are reset to zero each time the switch is restarted..

 

RxLoPriorityByte   

Rx lo-priority (default) octet count including bad packets. 

RxHiPriorityByte   

Rx hi-priority octet count including bad packets.

RxUndersizePkt   

Rx undersize packets w/good CRC. 

RxFragments 

 

Rx fragment packets w/bad CRC, symbol errors or alignment errors. 

RxOversize 

 

Rx oversize packets w/good CRC (max: 1536 or 1522 bytes). 

RxJabbers 

 

Rx packets longer than 1522B w/either CRC errors, alignment errors, or symbol errors

 

 

 

 

(depends on max packet size setting) or Rx packets longer than 1916B only. 

RxSymbolError 

 

Rx packets w/ invalid data symbol and legal preamble, packet size. 

RxCRCerror 

 

Rx packets within (64,1522) bytes w/an integral number of bytes and a bad CRC (upper 

 

 

 

 

limit depends up on max packet size setting). 

RxAlignmentError   

Rx packets within (64,1522) bytes w/a non-integral number of bytes and a bad CRC (upper limit 

 

 

 

 

depends on max packet size setting). 

RxControl8808Pkts  

The number of MAC control frames received by a port with 88-08h in EtherType field

RxPausePkts 

 

The number of PAUSE frames received by a port. PAUSE frame is qualified with EtherType (88-08h), 

 

 

 

 

DA, control opcode (00-01), data length (64B min), and a valid CRC. 

RxBroadcast 

 

Rx good broadcast packets (not including errored broadcast packets or valid multicast packets). 

RxMulticast 

 

Rx good multicast packets (not including MAC control frames, errored multicast packets or valid 

 

 

 

 

broadcast packets). 

RxUnicast 

 

Rx good unicast packets. 

Rx64Octets 

 

Total Rx packets (bad packets included) that were 64 octets in length. 

Rx65to127Octets   

Total Rx packets (bad packets included) that are between 65 and 127 octets in length. 

Rx128to255Octets   

Total Rx packets (bad packets included) that are between 128 and 255 octets in length.

Rx256to511Octets   

Total Rx packets (bad packets included) that are between 256 and 511 octets in length.

Rx512to1023Octets 

Total Rx packets (bad packets included) that are between 512 and 1023 octets in length.

Rx1024to1522Octets 

Total Rx packets (bad packets included) that are between 1024 and 1522 octets in length (upper limit

 

 

 

  

depends on max packet size setting). 

TxLoPriorityByte   

Tx lo-priority good octet count, including PAUSE packets. 

TxHiPriorityByte   

Tx hi-priority good octet count, including PAUSE packets. 

TxLateCollision 

 

The number of times a collision is detected later than 512 bit-times into the Tx of a packet. 

TxPausePkts 

 

The number of PAUSE frames transmitted by a port

TxBroadcastPkts   

Tx good broadcast packets (not including errored broadcast or valid multicast packets). 

TxMulticastPkts 

 

Tx good multicast packets (not including errored multicast packets or valid broadcast packets). 

TxUnicastPkts 

 

Tx good unicast packets. 

TxDeferred 

 

Tx packets by a port for which the 1st Tx attempt is delayed due to the busy medium. 

TxTotalCollision 

 

Tx total collision, half-duplex only. 

TxExcessiveCollision 

A count of frames for which Tx fails due to excessive collisions.

TxSingleCollision   

Successfully Tx frames on a port for which Tx is inhibited by exactly one collision. 

TxMultipleCollision  

Successfully Tx frames on a port for which Tx is inhibited by more than one collision.

Summary of Contents for 2-Port OABR Multi-Media-Switch





























Reviews: