background image

iCylinder2 SFT05 - Software 

v1.0 

 

iTEC

 

– PORTUGAL 

 

 

www.i-tec.com.pt   

 

 

 

4.1.2- Assembly Sequence   

1.The Outside Cylinder Components   

Please disassembly the cylinder components in following order; fixing screw (5), remove 

the Antenna (3), and Inner Assembly (1)   

 

 

 

 

 

 

 

 

 

 

 

 

Note:

 please be caution to take down the antenna.   

 

 

 

 

 

2.Locating iCylinder   

Insert the cylinder inner assembly (1) into the lock hole, (with the key hole in the lock pin is 

on the outside of the door). Adjust the cylinder positions to make the lock core positioning 

screw snap to the centre of the lock hole, and inserting the cylinder setscrew (6) into lock 

hole, then screw down it with the cylinder position screw hole.   

 

3. Routing Maintenance and Treatment   

 

1.  Protect  the  cylinder  from  touching  with  corrosive  substances  to  avoid  locking 

surface coat, and reduce the locking surface glossiness   

2. Handles and knobs have a direct impact on the flexibility of the lock for they are the 

key parts for the door, please do not hang anything on them.   

3. Please replace the new battery in time when the battery is weak. 

4. Please keep the mechanical keys well properly against unexpected needs. 

Summary of Contents for iCylinder2 SFT05



















Reviews: