3. Menu W
indow
91
(10) Controller (C) (continued)
▪ User Data Retained Memory (U)
In the case of X-SEL-P/Q/PX/QX, R/S/RX/SX/RXD/SXD,
RA/SA/RAX/SAX/RAXD/SAXD with gateway function, clear all the
contents of user data retained memory containing RC-axis position data in
X-SEL controller.
(PC interface software version 7.2.0.0 or later)
* If the Edit screen for RC-axis position (in X-SEL-P/Q/PX/QX and
R/S/RX/SX/RXD/SXD controllers) is opened without resetting the
software or turning off the power after performing this operation and
writing to the flash ROM, “RC Position NO. Error” message will be
displayed.
* If the software is reset or the power is turned off without writing to the
flash ROM after performing this operation, the last written data in the
flash ROM will be retained.
If the user data retained memory is initialized by a mistake, reset the
software without writing to the flash ROM.
* XSEL-RA/SA, RAX/SAX, RAXD/SAXD do not require flash ROM
writing after completing initialization of the user data retaining memory.
Only the software reset is required.
▪ Parameter (at the time of shipment) (S)
Can return parameters to the ones at the time of shipment. This item is not
displayed normally. It is a function which will become available by inputting
a password. (Refer to “8.5 How to Initialize X-SEL-R/S, RX/SX, RXD/SXD,
RA/SA, RAX/SAX, RAXD/SAXD and SSEL, ASEL, PSEL Parameters (at
the time of shipment).”)
It is a function of X-SEL-R/S, RX/SX, RXD/SXD, RA/SA, RAX/SAX,
RAXD/SAXD, SSEL, ASEL, and PSEL controllers.
[12] Absolute Reset (A)
Reset absolute data.
This item is not displayed for XSEL-PX/QX, RX/SX, RAX/SAX, TTA
(except for AC servo specification), MSEL-PC/PG controllers.
[13] Absolute Reset (Orthogonal Axis) (A)
Reset the absolute data of the orthogonal axis of the XSEL-PX/QX, RX/SX,
RAX/SAX controllers.
This item is displayed for XSEL-PX/QX, RX/SX, RXD/SXD controllers.
[14] Absolute Reset (SCARA Axis) (Q)
Reset the absolute data of the SCARA axis of the X-SEL-PX/QX, RX/SX,
RAX/SAX controllers.
This item is displayed for XSEL-PX/QX, RX/SX, RAX/SAX controllers.
[15] Calibration Home/Abs. Encoder Reset (A)
TTA (except for AC servo specification), MSEL-PC/PG, reset the absolute
data of SCARA axis of MSEL-PCX/PGX.
This item is displayed for MSEL-PCX/PGX controllers.
[16] Software Reset (R)
Execute software reset of the controller.
[17] Reset Error (E)
Reset errors present in the controller.
[18] Drive-source Recovery Request (P)
Issue a drive-source recovery request to the controller.
Summary of Contents for IA-101-X-MW
