IBC control F21009301 Manual Download

Page: 6 / 16

MANUFACTURER´S DECLARATION
DECLARATION OF CONFORMITY

Manufacturer

IBC control AB

Brännerigatan 5 A

SE-263 37 Höganäs

Sweden

Tel: +46 42 33 00 10

Product

Control unit for rotary heat exchanger

Type designation

MicroMax

Applicable

EU Directives

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

RoHS Directive 2011/65/EU including Delegated Directive EU2015/863

Applicable

UK Directives

The Electromagnetic Compatibility Regulations 2016

The Electrical Equipment (Safety) Regulations 2016

The Restriction of the Use of Certain Hazardous Substances in Electrical and

Electronic Equipment Regulations 2012

Harmonizing

standards for

EU/UK Directives

BS EN 61800-3:2004 - Emission kategori C1, Immunitet kategori C2

BS EN 61800-5-1/2 - The control unit is intended for installation in

environments with a pollution rating of 2 (Pollution degree 2)

This declaration of conformity is issued under the full responsibility of the

manufacturer

Höganäs 2021-09-01

IBC control AB

Christer Persson

Summary of Contents for F21009301

















Search results

Summary of Contents for F21009301

Reviews:

Related manuals for F21009301

Brands by name

Popular brands

IBC control F21009301, Manual

Search results

Summary of Contents for F21009301

Reviews:

Related manuals for F21009301

Brands by name

Popular brands