background image

IBC Technologies Inc. 

11 

VFC 15-150 and VFC 45-225 

1.4.1.6

 

Sidewall Vent Termination 

Sidewall direct vent applications shall be 
vented as follows: 

 

both the inlet and exhaust 
terminations should normally be 
located on the same plane (side) of 
the building, 

 

the exhaust outlet is to be placed so 
as to reach 24” minimum above the 
down-turned intake - to avoid 
exhaust re-ingestion. 

 

The elevation of both pipes can be 
raised in “periscope style” after 
passing through the wall, then 
configured as above, to gain 
required clearance. 

 

Use a 45° elbow on the exhaust 
termination to launch the plume up 
and off the sidewall, for protection 
of wall. 

 

bird screen of ¼” stainless steel or 
plastic mesh is useful to guard 
against foreign objects 

 

Figure 4 - Sidewall Vent Termination - Piping Configuration 

To promote the projection of exhaust away from the building and from the intake pipe, 
reduction of 3” pipe to 2” is permitted for a maximum lineal travel of 3’ including 2 x 
90°  elbows on each side. This allows for smaller wall penetrations, with sufficient travel 
allowance to achieve the minimum exterior configuration as shown above. 

For side venting of multiple boiler sets, group all intake terminals together with 4” to 8” 
lateral spacing, and similarly group the exhaust pipes. Place the 2 groups on the same 
plane of the building (e.g. north facing wall(s)). Place the 2 groups of pipes at least 3’ 
apart (the closest intake and exhaust pipes shall be 36” - or more – apart. Use same 24” 
(minimum) vertical separation as displayed above. 

Summary of Contents for VFC 15-150


























































Reviews: