background image

1-29

INSTALLATION

DC SERIES BOILERS / WATER HEATERS  

DC 15-95, DC 15-96, DC 20-125, DC 33-160

1.7.1 Domestic Hot Water System

The DC series boilers / water heaters have an independent piping circuit for 

efficiently generating Domestic Hot Water. When a faucet is opened to draw hot 

water, water flow is detected with a flow sensor and the DC Series boiler / water 

heater fires up to begin generating domestic hot water. Due to the unique design 

of the boiler’s heat exchanger, the boiler / water heater can fire with either no 

water in the alternate space heating circuit or without flow of water if pressurized 

with the heating system water.
The cast aluminum heat exchanger has two separate copper water passage-

way’s encased into the aluminum heat transfer block. Each copper passageway 

is completely isolated from the other to eliminate cross contamination in the event 

of a leak. This heat exchanger complies with the double wall heat exchanger 

requirements in many regional jurisdictions.
The unique design of the cast aluminum heat exchanger acts as a heat buffer, 

eliminating the cold sandwich effect when turning on and off the water repeatedly. 

The domestic hot water operation can be set to operate in 3 different ways. 

• 

Standard Mode:

 The boiler / water heater responds to a call for domestic hot 

water when a faucet is opened. After the faucet is closed the boiler / water 

heater shuts down and waits for a call for the faucet to open.

• 

Comfort Mode:

 After the faucet is closed the boiler / water heater will 

maintain the programmed domestic hot water temperature so that the next 

time the faucet is opened, hot water is delivered to the faucet immediately 

without the “Cold Water Sandwich” effect.

• 

Eco Comfort Mode:

 As above, the boiler / water heater will maintain the 

programmed domestic hot water temperature but based on a learned pattern, 

the boiler / water heater will allow the water to cool. For example during the 

night, the boiler / water heater will see no flow of domestic hot water therefore 

will allow the boiler / water heater to cool down each night. If hot water is 

required at night, the boiler / water heater will respond to an open faucet just 

as if it was in the Standard Mode.

While the DC Series boiler / water heater is less susceptible to lime scale build-

up than other units on the market, water quality must always be considered when 

installing the boiler / water heater. Treating hard water and adjusting the pH to 6.5 

and 8.5 is strongly recommended. As a reference 

Table 6 

represents some of the 

drinking water guidelines published by the US EPA. Consult a water treatment 

advisor in your area to assess your local needs. Proper water treatment will aid in 

the longevity of the boiler / water heater and ensure maximum efficiencies.

DESCRIPTION

MAX

MIN

Water Pressure

150 psi

40 psi

Programmable water temperature

149°F (65°C)

104°F (40°C)

Minimum Flow Rate to Activate DHW Sensor

N/A

0.5 GPM

Acceptable pH range

8.5 pH

6.5 pH

Chloride

250 mg/L

Iron

0.3mg/L

Total Dissolved Solids

500mg/L

Total Hardness

7 grains

Table 6: Water Quality

WARNING

A potentially hazardous situation, 

which can cause serious injury 

or death, can exist if the un-used 

domestic water connections are 

capped off. The unused domestic 

water connections are meant to 

be left open if not used to allow 

for the air in the coil to expand 

and contract as the boiler / water 

heater is in operation.

WARNING

Bacteria growth can develop in 

domestic hot water tanks and 

indirect water heaters if the 

minimum water temperature is 

not set high enough to prevent 

its growth.

WARNING

HOT WATER CAN SCALD!
Water Temperatures over 125°F 

/ 52°C can cause severe burns 

instantly or death from scalds.
Children, disabled, and elderly are 

at highest risk of being scalded.

 

Never leave them unattended 

in or near the shower, bathtub 

or sink.

 

Never allow small children to 

use a not water faucet or draw 

their own bath.

To avoid any potential scald 

hazard or if codes require specific 

water temperatures at the hot 

water faucet, the installer may:

 

Install a thermostatic mixing 

valve at this appliance and 

ensure it is working properly.

 

AND

 

Set the thermostatic mixing 

valve to the lowest temperature 

which satisfies your hot water 

needs.

TO AVOID INJURY:

 

Feel and adjust water 

temperature before bathing or 

showering.

 

Water drained from the system 

drain valve may be extremely 

hot.

 

Make sure all connections are 

tight.

 

Direct water flow away from 

any person.

Summary of Contents for DC Series



















































































Reviews: