background image

©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION

iBEAMUSA.com

iBEAM Vehicle Safety Sytems 

®

REV. 05/20/2020   INSTTE-WKMN5

Attention! 

When testing the aftermarket 

equipment, ensure that all factory equip-
ment is connected before cycling the key to 
ignition.

TE-WKMN5

INSTALLATION INSTRUCTIONS
#IBEAM

SAFETY

Installation............................................................2-3
Wireless Pairing .....................................................4
Display Settings .....................................................5
Wire Lenths ............................................................6
Specifications .........................................................7

TABLE OF CONTENTS

TOOLS REQUIRED

• Wire stripper
• Tape
• Digital Multi-meter
• Cutter

Universal

 Wireless 5” Monitor 

and Camera

Visit

 iBEAMUSA.com

 for more detailed informatuon about the product and up-to-date vehicle specific 

applications.

Product Features

•  Wireless camera and monitor kit
•  5” LCD Monitor
•  20 M / 65 FT range
•  DC socket for monitor power with USB for smart device charging
•  Video triggered by the camera’s signal

Part Components

A) Monitor       B) Camera w/ additional mount     C) Accessories

A

B

C

Summary of Contents for TE-WKMN5









Reviews: